Verarbeitung und eine tigen HELIX Verstärkers. überzeugende Anwendung ausgereifter Technolo- gien aus. Audiotec Fischer setzt mit der HELIX M SIX neue Viel Freude an diesem Produkt wünscht Ihnen das Maßstäbe im Bereich der Verstärkertechnik. Dabei profitieren Sie als Kunde direkt von unserer Team von mehr als 30-jährigen Erfahrung in der Forschung...
Anschluss- und Bedienelemente Line Input Cinch-Eingänge Anschluss eines Regler zum Einstellen des Tiefpassfilters Vorverstärkersignals. der Kanalpaare C/D und E/F von 40 Hz bis 4.000 Hz. Input Level Regler zum Einstellen der Eingangsemp- Subsonic / HPF findlichkeit des Line Inputs für die einzelnen Regler zum Einstellen des Subsonicfilters / Stereo-Kanäle.
Inbetriebnahme und Funktionen 1 Line Input Kanalpaares C/D die Übernahmefrequenz für den 6-Kanal Vorverstärkereingang zum Anschluss von Hochpass eingestellt werden. Bei Schalterstellung Signalquellen, wie z.B. Radios, die mit dem/den FULL (Fullrange) ist die interne Frequenzweiche Vorverstärkerausgang/-ausgängen bzw. Line Out- nicht aktiv. Bei Schalterstellung LPF (Tiefpassfilter / puts der Signalquelle verbunden werden können.
Seite 5
5 LPF nommen werden, wenn Sie einen Basslautsprecher Mit Hilfe dieser Regler kann das Tiefpassfilter von an die Lautsprecherausgänge E und F anschließen. 40 Hz bis 4.000 Hz für die Kanalpaare C/D und E/F 8 Power & Protect LED eingestellt werden. Die Power &...
Einbau und Installation 4. Anschluss des Remote-Eingangs Die HELIX M SIX wird wie nachfolgend beschrie- ben an das Autoradio angeschlossen. Der Remote-Eingang (REM) muss mit dem Remote-Ausgang des Steuergerätes (Radio) Achtung: Für die Durchführung der nachfolgenden verbunden sein, um den Verstärker mit dem Schritte werden Spezialwerkzeuge und Fachwissen Steuergerät ein- und auszuschalten.
Seite 7
Konfigurationsbeispiele 6-Kanal Anwendung mit 2 x 2 Ohm Subwoofer Kanal A/B Hochpassfilter Komponentensystem + Koaxialsystem + Subwoofer Vorne Links Rechts 50 - 100 Hz Kanal C/D Hochpassfilter Subwoofer SW 1 50 - 100 Hz Kanal E/F SW 2 Bandpass / Summiert Links Rechts Summed...
Technische Daten Leistung RMS / Max. - @ 4 Ohm ..............6 x 100 / 200 Watt - @ 2 Ohm ..............6 x 100 / 200 Watt - gebrückt an 4 Ohm ........... 3 x 200 / 400 Watt Verstärkertechnologie ..........
Seite 10
Spezielle Features der HELIX M SIX Start-Stopfähigkeit Das Netzteil im HELIX M SIX Verstärker stellt die interne Spannungsversorgung auch bei kurzfri- stigen Einbrüchen bis hinab zu 6 Volt sicher. Damit ist gewährleistet, dass die HELIX M SIX auch beim Motorstart voll funktionsfähig bleibt.
M SIX amplifier To prevent damage to the unit and possible injury, The HELIX M SIX amplifier may only be installed read this manual carefully and follow all installation in vehicles which have a 12 Volts negative terminal instructions. This product has been checked for connected to the chassis ground.
Seite 12
Connectors and control units Line Input RCA inputs for connecting lowlevel line Control for adjusting the lowpass filter of the signals. channel pairs C/D and E/F from 40 Hz to 4,000 Hz. Input Level Control for adjusting the input sensitivity of Subsonic / HPF the lowlevel Line Inputs for the individual ste- Control for adjusting the subsonic / high-...
Seite 13
Initial start-up and functions 1 Line Input By adjusting the highpass (control 3) and lowpass 6-channel lowlevel line input to connect signal filter (control 5 of the channel pair C/D) any band- sourc es such as head units / radios / DSPs. pass between 15 Hz and 4,000 Hz can be realized.
Seite 14
The amplifier is ready for operation. Red: A malfunction has occurred. A malfunc- tion may have different causes as the HELIX M SIX is equipped with several protection circuits. These protections shut off the amplifier in case of overheat- ing, over- and undervoltage, short-circuit on loudspeakers and false connection.
Installation 4. Connecting the remote input Connection of HELIX M SIX to the head unit / car radio: The remote input (REM) has to be connected to the radio remote output to switch the ampli- Caution: Carrying out the following steps will re- fier on and off together with the head unit / car quire special tools and technical knowledge.
Seite 16
Examples of speaker configurations 6-channel application with 2 x 2 Ohms subwoofer Channel A/B Highpass filter Component system + coaxial system + subwoofer Front Left Right 50 - 100 Hz Channel C/D Highpass filter Subwoofer VC 1 50 - 100 Hz Kanal E/F VC 2 Bandpass / Summed...
Seite 17
6-channel fully active application Channel A/B Highpass filter Tweeters + midrange speakers + mid-woofers Mid-woofers Left Right 3000 - 4000 Hz Channel C/D Bandpass Left Tweeters Highpass filter Lowpass filter 800 - 1000 Hz 3000 - 4000 Hz Channel E/F Right Bandpass / Stereo Left...
Dimensions (H x W x D) ..........50 x 320 x 154 mm / 2.00 x 12.60 x 6.06” Unique Features of the HELIX M SIX Start-Stop capability The switched power supply of the HELIX M SIX assures operation even if the battery’s voltage drops down to 6 Volts during engine crank.