Enabling Password Protection, Changing Passwords And Defining User Rights; Configuring Alarm Inputs - Monacor AXR-series Bedienungsanleitung

6.6 Enabling password protection, changing
passwords and defining user rights
According to the factory settings, access to the recorder is not
protected. The predefined password "admin" is not enabled,
i.e. it must not be entered to make any changes to the settings.
When the recorder is connected to a network, always make
sure to enable the password protection feature and to
change the password (also see chapter 2 "Important Data
Security Notes")
1) Call up the main menu, select the menu "System" and
there, on the left side, click the submenu "Users".
Parameter Record Search
General
No.
Users
Info
Log
Fig. 6-19 Menu for passwords and user groups
2) Line number 1 for the administrator password is selected.
To change the password and to enable the password pro-
tection feature, click the button "Edit".
User Edit
User Name admin
User Name admin
Password Enable Disable
Password
Confirm
Default Save
Fig. 6-20 Window to change passwords
3) Change the user name "admin", if desired.
4) Set the line "Password Enable" to "Enable": The user lock
will be activated after 2 minutes when no menu is displayed
and the recorder is not operated.
5) In the line "Password", enter a new password with a length
of at least 8 characters. Re-enter the password in the line
"Confirm".
Important: For remote recorder control and access via the
network, the password must consist of exactly 8 charac-
ters. It is possible to enter more characters; this password,
however, will be regarded as invalid by the software for
remote access.
6) To save the new password, click "Save". When the pass-
word has been successfully saved, a corresponding message
will appear; click "OK" to confirm.
7) To define user rights, first assign a user name and a pass-
word to each user as described above.
8) When a line for a user has been selected, the button
"Permission" will additionally appear at the bottom of
the menu. Click the button to define the user rights.
44
i
Device System Advanced
User Name Level
1 admin ADMIN
2 user1 USER1
3 user2 USER2
4 user3 USER3
5 user4 USER4
6 user5 USER5
7 user6 USER6
Cancel
User Name
Log Search
Disk Manage
Backup
Analog Channels
IP Channels
Live
Analog Channels
IP Channels
Playback
Analog Channels
IP Channels
PTZ
Analog Channels
IP Channels
Fig. 6-21 Menu for the user rights
Define the rights of the user selected and save them. If
applicable, repeat this procedure for any additional users.
9) To exit the menu, click "Cancel" or wait for the menu to
Shutdown
disappear after the time defined.
Enable
Enable
Disable

6.7 Configuring alarm inputs

Disable
Disable
When alarm sensors such as motion detectors or photoelectric
Disable
Disable
sensors are connected to the contacts SENSOR (27), configure
Disable
the alarm inputs by means of the menu "Parameter", submenu
"Alarm", section "Alarm".
Edit Cancel
Parameter
Display
Record
Capture
Network
Alarm
Motion
Alarm
Fig. 6-22 Menu for the alarm inputs
Menu item
Alarm In
Alarm Type
Latch Time
Buzzer
Post Recording
Alarm Out
Show Message
Send Email
Full Screen
Copy
Default
Save
Cancel
User Permission
user1
Parameter Maintain
Remote Login SEQ Control
1 2 3 4
1 2 3 4 5 6
1 2 3 4
1 2 3 4 5 6
1 2 3 4
1 2 3 4 5 6
1 2 3 4
1 2 3 4 5 6
All Clear Save Cancel
i
Record Search Device System
Alarm In IO-1
Alarm Type Normally-Open
Latch Timer 10 s
Buzzer OFF
Post Recording 30 s
Alarm Out
Show Message Send Email Full Screen
Record Channel
1 2 3 4
Analog Channels
1 2 3 4 5 6
IP Channels
Copy IO-1 To All
Function
To select the alarm input
To select the contact type
Normally-Open
Normally-Close
OFF = input signal will not be evaluated
I
Time the symbol will appear in the live image
and time the camera image will be displayed in
full-screen mode
Duration of the alarm sound
Duration of an alarm-triggered recording
The alarm will be routed to the output ALARM (27)
In the live image, an alarm will be indicated by the
I
symbol
In case of an alarm, an e-mail will be sent;
for the e-mail settings, refer to menu "Parameter",
submenu "Network", section "Email"
The corresponding channel will be displayed in the
full-screen mode
To use the settings of an alarm input for additional
inputs
Reset to factory settings
To save the setting
To exit the menu
Manuel Record
Manual Capture
Shutdown
Advance
Copy
Default Save Cancel