Frequently Asked Questions - Monacor AXR-series Bedienungsanleitung

11 Frequently Asked Questions

sorted alphabetically by search terms
Audio recording
How can I record sound?
The AXR recorders provide audio inputs with line level. For
audio recordings, a microphone and a small microphone
preamplifier or a small mixer are required.
Configuration example:
MPA-102 (microphone preamplifier) and
ECM-302B (boundary microphone)
Cloud
Can I save images to a cloud?
The AXR recorders support alarm uploads to the cloud of the
provider DROPBOX. For alarm recordings due to motion de-
tection or I / O alarm, JPEG images can be loaded to the cloud.
Data rate
What is the total data rate available for recordings?
Model
Number of channels for analog cameras
Data rate for analog cameras
Additional channels for IP cameras
Data rate for IP cameras
Total data rate
When a channel for an analog camera is switched off, an
additional IP camera can be used instead.
No image
Why is there no image on the monitor connected?
Please check the resolutions supported by your monitor. The
resolution at the HDMI monitor output of the recorder is
factory-set to 1280 × 1024 pixels. The AXR-... supports the
following resolutions:
1024 × 768
1080 × 1024
1280 × 720
1440 × 900
1920 × 1080
IP cameras
Which IP cameras can be used with the AXR recorders?
IOC-2812BVM
IOC-2812DVM
The following IP cameras are supported as well; however,
please note that some restrictions apply (e. g. no alarm
recordings, no audio):
All models of the INC series
58
AXR-104 AXR-108 AXR-116
4 8 16
16 Mbps* 32 Mbps* 64 Mbps*
2 4 8
8 Mbps 16 Mbps 32 Mbps
24 Mbps 48 Mbps 96 Mbps
* 4 Mbps per camera
Mobile phone
How can I get camera images onto my mobile phone?
A short video clip (only available in German) explains how to
set up remote access to an AXR recorder via a smartphone:
https://youtu.be/13P1Y4PiBmk
OSD menu of an AXC camera
How can I call up the OSD menu of an AXC camera via
the AXR recorder?
The OSD menu of the camera can be called up via the PTZ
console of the AXR:
1) In the main menu, select "Device"/"PTZ" and then change
the PTZ protocol from "Pelco-D" to "COAX1" (baud rate
9600).
2) The function "IRIS+" of the PTZ console can now be used
to call up the OSD menu of the AXC camera.
3) To navigate within the menus, use the arrow buttons of
the PTZ console; for the "ENTER" function, use "IRIS+".
Recording time
What is the recording time possible?
The rule of thumb is:
1 GB/hour for each connected camera with CVBS signal
4 GB/hour for each connected camera with Full HD resolution
(1920 × 1080 p)
Remote access to camera images
How can I retrieve camera images to include them into
my homepage or a video door phone system?
It is possible to access connected cameras via the RTSP stream
which is provided by the AXR recorder. For detailed address
information, please refer to "RTSP" in the network menu of
the recorder.
Replacement for older cameras
Which cameras can be used as a replacement for older
cameras?
The cameras of the AXC series (with the exception of AXC-
137NLC and AXC-137PHC), offering the two signal outputs
TVI and AHD / CVBS are not only interesting as a replacement
for older cameras, but can also be part of sophisticated and
complex installations such as the surveillance system of an
entrance door: While the TVI signal is sent to a recorder, the
CVBS signal can be sent to a small monitor (e. g. TFT-800LED)
at the same time.