Remote Control Of Cameras (Ptz); Enabling The Snapshot Feature - Monacor AXR-series Bedienungsanleitung

Menu item Function
1. Click
the motion detection feature.
2. The motion-sensitive fields are marked in red. To
deactivate multiple fields, keep the left mouse
button pressed and move the mouse pointer
over the respective fields.
Area
3. It is possible to directly click individual fields.
4. The same procedure can be used to reactivate
fields.
5. To go back to the menu, click the right mouse
button in the camera image.
Duration of a recording that has been started via
Post Recording
the motion detection feature
Duration of the alarm ( M inserted, alarm sound,
Latch Time
alarm relay will respond)
When an alarm is detected, the alarm relay will
Alarm Out
respond (output ALARM, chapter 5.4)
A detected motion will be indicated by the symbol
Show Message
M (Motion)
When a motion is detected, an e-mail will be auto-
matically sent provided that the required specifica-
Send Email
tions have been made in the menu "Parameter",
submenu "Network", section "Email".
When a motion is detected, the corresponding
Full Screen camera image will be displayed in the full-screen
mode.
Specification of the channels that are to be recorded
when a motion is detected (it is possible to record
multiple channels even when the motion has been
detected in one channel only).
The times of a motion-triggered recording must be
Record Channel
entered in the record schedule (menu "Parameter",
submenu "Record", section "Record schedule";
click the yellow, round-shaped selection field
"Motion" and, with the left mouse button pressed,
move the mouse pointer over the days/hours).
To use the settings of a camera channel for addi-
Copy
tional channels
Default Reset to factory settings
Save To save the setting
Cancel To exit the menu

6.12 Remote control of cameras (PTZ)

For remote control of the cameras connected to the RS-485
interface (27), make the required settings at the recorder. Call
up the menu "Device" and click the submenu "PTZ".
Parameter Record Search
HDD
Channel
PTZ
Protocol
Cloud
Baudrate
DateBit
StopBit
Parity
Cruise
Address
Copy CH1
Fig. 6-26 Menu to set the remote control of cameras
Menu item Function
Channel To select the camera channel
Protocol To select the control protocol of the camera
Baudrate
To select the data transmission rate
DataBit Number of data bits
StopBit Number of stop bits
Type of parity bit:
Parity
None, Odd, Even, Mark (always 1), Space (always 0)
46
Setup to exclude specific detection fields for
i
Device System Advance
CH1
Pelco-D
9600
8
1
None
Enable
001
To All Copy
Default Save
Menu item
Cruise
Address
Copy
Default
Save
Cancel
Please refer to the specifications of the camera for the settings
concerning protocol, baud rate, data bit, stop bit and address.

6.13 Enabling the snapshot feature

The snapshot feature allows you to save camera snapshots
manually and in a time-controlled manner. Call up the menu
"Parameter" and then click the submenu "Capture".
Parameter
Display
Record
Capture
Capture
Capture Schedule
Network
Alarm
Bewegung
Fig. 6-27 Menu to enable the snapshot feature
Menu item
Channel
Auto Capture
Stream Mode
Normal Interval
Alarm Interval
Manual Capture
Copy
Default
Save
Cancel
Shutdown
To define the times at which snapshots are to be taken auto-
matically, click the section "Capture Schedule":
Parameter
Display
Record
Capture
S
Cancel
Capture
M
Capture Schedule
T
Network
W
Alarm
T
F
S
Bewegung
Fig. 6-28 Schedule for time-controlled snapshots
1) After "Channel", a camera channel is selected (here: chan-
nel 1). To change the recording time of a different channel,
click the symbol
Function
To enable or disable the camera cruise feature
Address of the camera for independent control of
all cameras connected
To use the settings of a camera channel for addi-
tional channels
Reset to factory settings
To save the setting
To exit the menu
i
Record Search Device System
Channel CH1
Auto Capture AUS
Stream Mode Mainstream
Normal Interval 5 s Alarm Interval 5 s
Manual Capture Disable
Copy CH1 To All
Function
To select the camera channel
To enable time-controlled snapshots (set the record-
ing times in the section "Capture Schedule")
"Mainstream" = high resolution, high data volume
"Substream"= lower resolution, lower data volume
Intervals between recordings in normal mode
Intervals between recordings in case of an alarm
To enable manual snapshots
(see chapter 7.6.2 on how to take snapshots)
To use the settings of a camera channel for addi-
tional channels
Reset to factory settings
To save the setting
To exit the menu
i
Record Search Device System
Channel CH1 Normal Motion
0 2 4 6 8 10 12 14
Copy CH1 To All

.
Advance Shutdown
Copy
Default Save Cancel
Advance Shutdown
Alarm
16 18 20 22
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Copy
Default Save Cancel