Operation - Makita DLS713 Bedienungsanleitung

OPERATION

NOTICE:
Before use, be sure to release the handle from the
•
lowered position by pulling the stopper pin.
Do not apply excessive pressure on the handle
•
when cutting. Too much force may result in
overload of the motor and/or decreased cutting
efficiency. Push down handle with only as much
force as is necessary for smooth cutting and
without significant decrease in blade speed.
Gently press down the handle to perform the cut. If
•
the handle is pressed down with force or if lateral
force is applied, the blade will vibrate and leave a
mark (saw mark) in the workpiece and the
precision of the cut will be impaired.
During a slide cut, gently push the carriage toward
•
the guide fence without stopping. If the carriage
movement is stopped during the cut, a mark will be
left in the workpiece and the precision of the cut
will be impaired.
WARNING:
Make sure the blade is not contacting the
•
workpiece, etc. before the switch is turned on.
Turning the tool on with the blade in contact with
the workpiece may result in kickback and serious
personal injury.
1. Press cutting (cutting small workpieces)
Fig.33
Workpieces up to 52 mm high and 97 mm wide can
be cut in the following manner.
Push the carriage toward the guide fence fully and
tighten two clamp screws which secure the slide
poles clockwise to secure the carriage. Secure the
workpiece with the proper type of vise. Switch on
the tool without the blade making any contact and
wait until the blade attains full speed before
lowering. Then gently lower the handle to the fully
lowered position to cut the workpiece. When the
cut is completed, switch off the tool and WAIT
UNTIL THE BLADE HAS COME TO A COMPLETE
STOP before returning the blade to its fully
elevated position.
WARNING:
Firmly tighten two clamping screws which
•
secure the slide poles clockwise so that the
carriage will not move during operation.
Insufficient tightening of the locking screw may
cause possible kickback which may result in
serious personal injury.
2. Slide (push) cutting (cutting wide workpieces)
Fig.34
Loosen two clamp screws which secure the slide
poles counterclockwise so that the carriage can slide
freely. Secure the workpiece with the proper type of
vise. Pull the carriage toward you fully. Switch on the
tool without the blade making any contact and wait
until the blade attains full speed. Press the handle
down and PUSH THE CARRIAGE TOWARD THE
GUIDE FENCE AND THROUGH THE WORKPIECE.
When the cut is completed, switch off the tool and
WAIT UNTIL THE BLADE HAS COME TO A
COMPLETE STOP before returning the blade to its
fully elevated position.
WARNING:
Whenever performing a slide cut, first pull the
•
carriage full towards you and press the handle
all the way down, then push the carriage
toward the guide fence. Never start the cut with
the carriage not pulled fully toward you. If you
perform the slide cut without the carriage pulled
fully toward you unexpected kickback may occur
and serious personal injury may result.
Never attempt to perform a slide cut by pulling the
•
carriage towards you. Pulling the carriage towards
you while cutting may cause unexpected kickback
resulting in possible serious personal injury.
Never perform the slide cut with the handle locked
•
in the lowered position.
Never loosen the knob which secures the
•
carriage while the blade is rotating. A loose
carriage while cutting may cause unexpected
kickback resulting in possible in serious personal
injury.
3. Miter cutting
Refer to the previously covered "Adjusting the
miter angle".
4. Bevel cut
Fig.35
Loosen the lever and tilt the saw blade to set the
bevel angle (Refer to the previously covered
"Adjusting the bevel angle"). Be sure to retighten
the lever firmly to secure the selected bevel angle
safely. Secure the workpiece with a vise. Make
sure the carriage is pulled all the way back toward
the operator. Switch on the tool without the blade
making any contact and wait until the blade attains
full speed. Then gently lower the handle to the fully
lowered position while applying pressure in parallel
with the blade and PUSH THE CARRIAGE
TOWARD THE GUIDE FENCE TO CUT THE
WORKPIECE. When the cut is completed, switch
off the tool and WAIT UNTIL THE BLADE HAS
COME TO A COMPLETE STOP before returning
the blade to its fully elevated position.
15