Noise/Vibration Information - Bosch GHO Professional 16-82 Originalbetriebsanleitung

OBJ_BUCH-2577-001.book Page 13 Tuesday, October 6, 2015 11:33 AM
13 Carbide blade (TC)
14 Hex key
15 Extraction hose (Ø 35 mm)*
16 Chip/dust bag*
17 Parallel guide
18 Scale for rebating width
19 Locking nut for adjustment of rebating width
20 Fastening bolt for parallel and beveling guide
21 Angle stop*
22 Locking nut for angle adjustment
23 Fastening bolt for rebating depth stop
24 Rebating depth stop*
25 Park rest
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Planer
Article number 3 601 EA4 0.. 3 601 EA4 3..
Rated power input W
-1
No-load speed min
Planing depth mm
Rebating depth mm
Planing width, max. mm
Weight according
to EPTA-Procedure
01:2014 kg
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-14.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-14:
2 2
a =8 m/s , K=1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
Bosch Power Tools
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with all
relevant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-14.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
GHO 16-82 GHO 26-82 D
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
630 710
Engineering
18000 18000
0 – 1.6 0 – 2.6
0 – 9 0 – 9
82 82
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 06.10.2015
3.4 3.4
/II /II
Assembly
 Before any work on the machine itself, pull the mains
Changing the Tool
 Be cautious when replacing the planer blades. Do not
Use only original Bosch carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and can be re-
versed. When both cutting edges are dull, the planer blade 13
must be replaced. The carbide blade (TC) may not be resharp-
ened.
Disassembling the Planer Blade(s) (see figure A)
To reverse or replace the planer blade 13, rotate the blade
drum 10 until it is parallel to the planer base plate 7.
 Loosen the two fastening screws 12 with the Hex key 14
 If necessary, loosen the clamping element 11 by giving it
 Push the planer blade 13 sidewards out of the blade drum
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
plug.
grasp the planer blades by the cutting edges. Possible
danger of injury due to the sharp cutting edges of the plan-
er blades.
by approx. 1 – 2 turns.
a light blow with a suitable tool (e.g. a wooden wedge).
10 with a piece of wood.
English | 13
1 609 92A 1AA | (6.10.15)