Paramondo EASY Montageanleitung Seite 6

Sicherheitshinweise • Safety instructions • Veiligheidsadviezen • Indicaciones de seguridad • Consig-
6
nes de sécurités • Avvertenze di sicurezza • Wskazówki dot. bezpieczeństwa • Güvenlik uyarıları
Extraction forces of the wall plugs:
In the following chart, you can find the extraction
forces of wall plugs expressed in Newton (N) per fixing
screw. The values refer to the assembly on non-cracked
concrete (C20/25)
Size
250 cm x 200 cm
295 cm x 200 cm
350 cm x 250 cm
395 cm x 250 cm
The extraction forces express the force necessary to extract a screw
from the wall. Here it will not be distinguished if the screw comes out
of the wall with the plug, if the screw or the masonry breaks.
The extraction forces declare how strongly screws and / or plugs can
be vertically strained. The fixing material must be determined on the
basis of the mounting surface, the kind of assembly and the extracti-
on forces.
The awning has a wind resistance class 2 and must be
retracted in case the wind force is higher than 5. The
following chart explains the classes and shows the wind
speed and its effects.
Class Wind force Wind speed
0 1 -3 up to 19 km/h
1 4 20 - 28 km/h
2 5 29 - 38 km/h
3 6 39 - 49 km/h
Instructions for the assembler and the user:
All the operating instructions, assembly instructions as well as adjust-
ment instructions of the manufacturer of the motor, of the switcher
and of the control must be given to the user with a guide.
He must be comprehensively informed about the safety information
and user instructions of the awning. Failure to observe this informa-
tion and incorrect operation may cause damage to the awning and
accidents. The instructions must be kept and must be handed to the
new owner in case of the awning is given to a third. According to the
knowledge of the local conditions and of the executed assembly, the
installation company declares to the user if the wind resistance class
indicated by the manufacturer has been achieved in mounted con-
dition. If not, the installation company must document the actually
achieved wind resistance class.
The user and the assembler shall be responsible for proper functio-
ning of the wind monitoring system and its regular check and function
monitoring. In case of storm damage occurred in spite of wind mo-
N/Number of brackets
Wall Ceiling
435/2 705/2
526/2 824/2
847/2 1288/2
981/3 1451/3
Effects
Leaves and thin twigs
move
Twigs and thin branches
move, loose paper is lifted
from the floor
Branches move and small
deciduous trees fluctuate
Thick branches fluctua-
te, umbrellas used with
difficulty
www.paramondo.de
nitoring, the supplier and manufacturer of the awning do not accept
any warranty. Sensors with sun monitoring must be turned off over
the winter.
Care and maintenance:
The awning is basically maintenance-free. All aluminium parts have
a high-quality powder coating, as well as the screw connections of
galvanised steel. We advise to clean the awning every 6 weeks with a
damp cloth. The awning cloth has a high-quality coating and is there-
fore suitable for outside use.
If the awning cloth becomes wet by rain, nothing will happen. The
awning cloth may be rolled up wet, too. However, in this case, we
advise to roll it out again and let it dry when it does not rain anymore.
We advise for the cleaning a solution of laundry detergent and a soft
brush. You can achieve good results in case of stubborn stains also
with a rubber. Never clean by means of a high-pressure device, becau-
se it damages the waterproofing.
Produkteigenschaften von Markisentüchern
Wir verarbeiten in unseren Markisen ausschließlich hochwertige Po-
lyestertücher. Die Fasern der Webgarne sind spinndüsengefärbt und
dadurch auch UV-beständig (farb- und lichtecht).
Eine Veredelung der Oberfläche verleiht dem Tuch wasserabstoßende
und schmutzabweisende Eigenschaften. So wird auch Schimmelbil-
dung vorgebeugt.
Important consumer information:
Awning covers are high-performance products. However, limits to
their perfection are set by environmental protection requirements
and with the current state of technology. Certain phenomena in the
fabric, which sometimes are subject of complain, are possible in spite
of sophisticated manufacture and processing technology.
Such phenomena do not diminish the value and the usability of the
awning. To prevent irritation, we would like to expressly point out the
following properties, within the scope of consumer awareness:
Img. 1 Img. 2
Img. 4
Bending folds
They originate at the moment of the manufac-
ture and when the sun protection fabric is fol-
ded. A dark line, which originates because of
the folding of the fibre, may become visible in
back light particularly in case of bright colours
(Light refraction). (Img. 1)
Waviness in the seam and length area
It can occur in the side seams, in the vicinity of the seams and in the
centre of the lengths. The cover is laid double on the seams. This
results in different rolling diameters.
The tension that arises due to the folding arms and the drooping of
the roller tube and/or the front profile may enhance these effects.
Waviness can originate if a water pocket forms during heavy rain.
(Img. 2,3)
Img. 3