Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
8.1 Connection
GB
As a DMX interface, the unit is equipped with
3-pole XLR connections of the following pin config-
uration:
Pin 1 = ground, pin 2 = DMX-, pin 3 = DMX+
For connection, use special cables for DMX signal
transmission (e. g. cables of the CDMXN series
from "img Stage Line"). For cable lengths exceed-
ing 150 m, it is generally recommended to insert a
DMX level matching amplifier (e. g. SR-103DMX
from "img Stage Line").
1) Connect the control input DMX IN (10) to the
DMX output of the light controller or to the DMX
output of another DMX-controlled unit.
2) Connect the control output DMX OUT (11) to the
control input of the following DMX-controlled
unit. Connect the output of this DMX-controlled
unit to the input of the following unit etc. until all
DMX-controlled units have been connected in a
chain.
3) To prevent interference in signal transmission, in
case of long cables or a multitude of units con-
nected in series, terminate the control output of
the last DMX unit in the chain with a 120 Ω resis-
tor (> 0.3 W): Connect a corresponding terminat-
ing plug (e. g. DLT-123 from "img Stage Line") to
the output jack.
8.2 Setting the number of DMX channels
To operate the spotlight with a light controller, the
DMX start address (
ber of DMX channels must be set. The number of
DMX channels depends on the functions required
and may also depend on the number of control
channels available at the light controller. Please
refer to chapter 10.1 for more information on the
functions available for operation with a different
number of channels, and then select the number of
DMX channels accordingly:
1) Press the button MENU to call up the setting
menu.
2) Use the button
Channel Mode
to call up this menu item.
3) Use the button
number of channels:
14Chan
,
16Chan
4) Press the button ENTER.
5) To exit the menu, keep the button MENU
pressed for more than one second (or wait for
one minute).
20
chapter 8.3) and the num-
or
to select the menu item
and press the button ENTER
or
to select the desired
1Chan
,
9Chan
,
12Chan
,
28Chan
8.3 Setting the start address
For separate control of all DMX units connected to
the light controller, each unit must have its own
start address. Example: If the first DMX channel of
the spotlight is to be controlled by the light con-
troller via DMX address 5, set the start address on
the WASH-400LED to 5. All other DMX channels of
the spotlight will be automatically assigned to the
following addresses.
Example for 12 channels:
When start address 5 is used for channel 1, the channels
2 to 12 will be assigned to the addresses 6 to 16; address
17 will be the next possible start address for the following
DMX-controlled unit.
1) Press the button MENU to call up the setting
menu.
2) Press the button ENTER to call up the menu
DMX Addres
item
3) Use the button
start address (
001
4) Press the button ENTER.
5) To exit the menu, keep the button MENU
pressed for more than one second.
After the start address has been set, the spotlight
can be operated via the DMX controller. The LED
DMX (2) lights up to indicate that control signals are
being received. The display (4) indicates the num-
ber of DMX channels and the start address that has
been set, e. g.:
12Chan:
005
9
Additional Functions
9.1 Inverting the pan direction
To match the pan direction of the spotlight, for
example, to other jointly controlled spotlights:
1) Press the button MENU to call up the setting
menu.
2) Use the button
Pan Inverse
call up this menu item.
,
3) Use the button
tion is to be inverted (
4) Press the button ENTER.
5) To exit the menu, keep the button MENU
pressed for more than one second.
.
or
to set the desired DMX
to
512
).
or
to select the menu item
and press the button ENTER to
or
to define if the pan direc-
Yes
) or not (
No
).
Werbung
Kapitel
Inhaltsverzeichnis
