Standard Battery Charger; Maintenance; Maintenance Intervals; Cleaning And Disinfecting - Dräger X-plore 8000 Gebrauchsanweisung

en |

Maintenance

4.2.2 Standard battery charger

Fault Cause
General error or
defect
Status LED is
flashing red.
5 Maintenance
5.1

Maintenance intervals

Work to do

Clean and disinfect the device

Visual inspection

Replacing the O-ring at plug-in or bayo-
net-type hose connector
1) for gas-tight packed devices, otherwise every 6 months
5.2

Cleaning and disinfecting

CAUTION
Health hazard
The undiluted agents are damaging to health if they come into
direct contact with the eyes or skin.
► Wear safety goggles and protective gloves when working
with these agents.
NOTICE
Potential damage to components
► Only use the prescribed processes and the cleaning and
disinfection agents specified for cleaning and disinfecting.
Other agents, methods, dosages and contact times may
damage the components.
5.2.1 Clean and disinfect the device
1. Dismantling the device:
a. Separate breathing hose, facepiece and fan unit from
each other.
b. Disconnect the carrying system from the fan unit.
c. If available, dismantle any accessories (e.g. hose and
device sleeves).
d. Dismantle the splash guard cover and filter (see
chapter 5.3.3 on page 12).
2. Clean the facepiece according to the appropriate
Instructions for Use.
3. Cleaning the breathing hose and carrying system:
22
Remedy
Re-insert the
rechargeable bat-
tery in the battery
charger. If the error
occurs repeatedly
have Dräger Ser-
vice check the bat-
tery charger and
rechargeable bat-
tery.
4. Clean and disinfect fan unit and splash guard cover using
In cases of strong contamination, the fan unit can be rinsed
under running water as follows.
1. Make sure the rechargeable battery remains inserted.
2. Close suction inlet and tube connection with plug
5.3
1)
X
5.3.1 Visual inspection
1)
X
Check all parts thoroughly and replace damaged parts if
necessary. In particular, check the filter sealing surface and
X
O-rings of the fan unit for damage (e.g. scratches) or
contamination.
5.3.2 Replacing or charging the rechargeable
Explosion, fire or chemical hazard!
► Do not remove, insert or charge rechargeable batteries in
► Keep rechargeable batteries away from sources of heat.
► Do not short-circuit the rechargeable battery contacts.
► Only use recommended rechargeable batteries.
Removing the rechargeable battery:
1. Fold up carrying system if necessary.
2. Push battery lock button. Ensure that the rechargeable
3. Remove rechargeable battery.
Inserting the rechargeable battery:
1. Fold up carrying system if necessary.
2. Position the two lower connection points of the
3. Fold the rechargeable battery in until it snaps audibly into
1) Sekusept® and Incides® are registered trademarks of Ecolab
2) Incidin® is a registered trademark of Ecolab USA Inc.
a. Clean all parts with luke-warm water using Sekusept
1)
Cleaner and a soft cloth (temperature: max. 30 °C,
concentration depending on contamination: 0.5 - 1 %).
b. Rinse all parts thoroughly under running water.
c. Prepare a disinfectant bath of water and Incidin
2)
Rapid (temperature: max. 30 °C, concentration:
1.5 %)
d. Place all parts to be disinfected into the disinfectant
bath (duration: 15 minutes).
e. Rinse all parts thoroughly under running water.
f. Allow all parts to air-dry or dry them in the drying
cabinet (temperature: max. 60 °C). Keep away from
direct sunlight.
®
Incides N disinfectant cloths
Water must not enter the battery compartment.
(available as accessories).

Maintenance work

battery
WARNING
potentially explosive or flammable environments.
battery does not fall down.
rechargeable battery at an angle in the battery
compartment sockets.
place.
Deutschland GmbH.
Instructions for use
®
*
.
| Dräger X-plore® 8000
®