Kenwood FP260 series Bedienungsanleitung Seite 6

to use your food processor
1 Fit the detachable shaft onto the power unit
2 Then fit the bowl. Place the handle towards the back and turn
clockwise until it locks
3 Fit an attachment over the drive shaft.
●
Always fit the bowl and attachment onto the machine before
adding ingredients.
4 Fit the lid - ensuring the top of the drive shaft locates into the
centre of the lid.
●
Do not use the lid to operate the processor, always
use the on/off speed control.
5 Switch on and select a speed.
●
The processor won't work if the bowl and lid are
fitted incorrectly.
●
Use the pulse control for short bursts. The pulse will operate as
long as the control is held in position.
6 Reverse the above procedure to remove the lid, attachments and
bowl.
●
Always switch off before removing the lid.
important
●
Your processor bowl is not suitable for crushing or grinding
coffee beans, or converting granulated sugar to caster sugar.
●
When adding almond essence or flavouring to mixtures avoid
contact with the plastic as this may result in permanent marking.
to use your liquidiser
1 Fit the sealing ring into the blade unit
located correctly. Leaking will occur if the seal is
damaged or not fitted correctly.
2 Screw the goblet onto the blade assembly
The liquidiser will not work if incorrectly assembled.
3 Put your ingredients into the jug.
4 Fit the lid to the goblet and push down to secure
cap.
5 Place the liquidiser onto the power unit and turn clockwise to
lock .
6 Select a speed or use the pulse control.
safety
●
Liquids should be allowed to cool to room
temperature before blending.
●
Always take care when handling the blade assembly and avoid
touching the cutting edge of the blades when cleaning.
●
Only operate the liquidiser with the lid in place.
●
Only use the goblet with the blade assembly supplied.
●
Never run the liquidiser empty.
●
To ensure the long life of your liquidiser, do not run it for longer
than 60 seconds.
●
Smoothie recipes - never blend frozen ingredients that have
formed a solid mass during freezing, break it up before adding to
the goblet.
hints
●
When making mayonnaise, put all the ingredients, except the oil,
into the liquidiser. Remove the filler cap. Then, with the appliance
running, add the oil slowly through the hole in the lid.
●
Thick mixtures, e.g. pâtés and dips, may need scraping down. If
the mixture is difficult to process, add more liquid.
●
Ice crushing - operate the pulse in short bursts until crushed to the
desired consistency.
●
The processing of spices is not recommended as they may
damage the plastic parts.
.
.
- ensuring the seal is
.
. Fit the filler
●
The appliance will not work if the liquidiser is incorrectly fitted.
●
To blend dry ingredients - cut into pieces, remove the filler cap,
then with the appliance running, drop the pieces down one by
one. Keep your hand over the opening. For best results empty
regularly.
●
Don't use the liquidiser as a storage container. Keep it empty
before and after use.
●
Never blend more than 1.2 litres - less for frothy liquids like
milkshakes.
to use your mill
Use the mill for milling herbs, nuts and coffee beans.
1 Put the ingredients into the jar
2 Fit the sealing ring
3 Turn the blade unit upside down. Lower it into the jar, blades
down.
4 Screw the blade unit onto the jar until finger tight
5 Place the mill onto the power unit and turn clockwise to lock
6 Switch onto maximum speed or use the pulse control.
safety
●
Never fit the blade unit to your food processor without the jar
fitted.
●
Never unscrew the jar while the mill is fitted to your appliance.
●
Do not touch the sharp blades – Keep the blade unit away from
children.
●
Never remove the mill until the blades have completely stopped.
●
To ensure the long life of your mill, never run for longer than
30 seconds. Switch off as soon as you have got the right
consistency.
●
The processing of spices is not recommended as they may
damage the plastic parts.
●
The appliance will not work if the mill is incorrectly fitted.
●
Use for dry ingredients only.
hints
Herbs are best milled when clean and dry.
3
.
into the blade unit .
.
.