Product Familiarisation; Intended Use - Silverline 951855 Übersetzung Der Originalbetriebsanleitung

951855
• Use the correct type of cutting or grinding disc for the task and material.
Check the label on the disc or accessory to find out if it is appropriate to use on the
workpiece
• If discs are supplied with blotters they must be fitted and used correctly.
Not fitting blotters may cause the disc to shatter in use and be a safety risk
• Ensure the cutting/grinding disc or accessory is fitted correctly and securely
before use. Run the machine with the disc or accessory fitted, but without load,
for a reasonable time before attempting to cut/grind. If excessive vibration occurs,
stop the machine, investigate and correct the cause before use. Seek professional
guidance if you are in doubt about how to operate the machine safely
• Do not allow discs to become wet or contaminated with oil. If you suspect
a disc has degraded in storage, or if you are unsure whether its expiry date has
passed, DO NOT USE AND DISCARD
• Do not attempt to cut or grind magnesium or any alloy that has high
magnesium content
• Hold the machine appropriately to ensure that debris produced does not land
on skin or clothing
• Do not touch the spindle lock button while the tool is operating
• A grinding disc will gradually wear down during use, reducing its size. If a disc
becomes too small to work with easily, stop using it and replace it with a new disc
Additional Safety For Super Abrasives
• Superabrasives are generally inflexible and could shatter, so must be handled
with the utmost care. Damaged or improperly mounted superabrasives are
dangerous and can cause SEVERE injury to the user and other people in the vicinity
• Types of superabrasive wheels include diamond cutting discs, welded
metal discs, CBN discs etc. Choose your superabrasive tool carefully, taking into
consideration the workpiece material, the machine dimensions and capabilities.
Make sure the machine does not exceed the maximum operating speed of the
superabrasive disc
• NEVER use superabrasive cutting discs for side grinding, as this might lead to
the disc shattering
• Superabrasive wheels have to be carefully inspected and tested before
mounting. Metal wheels should be subjected to a sound test: hold the wheel on a
mandrel or with a finger inserted through the bore, then tap it with a non-metallic
object at several points and listen each time to the sound produced. An intact wheel
will produce a clear 'bell like' metallic sound. Damaged wheels will give a dull,
chattering sound. If in doubt, DO NOT USE, MARK AS DAMAGED AND DISCARD
• Make sure the machine's mounting flange is compatible with the
superabrasive wheel. Refer to the manufacturer's mounting instructions
• ALWAYS conduct a test run after mounting, with no load for at least 30
seconds, to determine if the wheel runs balanced and does not produce
excessive vibration. If it does, switch off IMMEDIATELY, remove the disc, inspect,
re-mount and re-test if no damage is detected
• If planning on using the superabrasive wheel with a coolant, liquid dust
suppressant or lubricant, first check if the wheel, machine and workpiece are
compatible with wet cutting and with the compound to be used. Always apply
liquid to an already running wheel, never to a non-moving tool, as the unbalance
could lead to the rupture of the wheel. When switching off, remove the liquid supply
first and let the machine run at no-load, until centrifugal forces have drained all
liquid from the wheel. Dry off the wheel after use, and prevent liquid from being
absorbed into the wheel
2400W Angle Grinder 230mm

Product Familiarisation

1 Auxiliary Handle
2 Handle Thread (Right)
3 Motor Vents
4 Handle Thread (Left)
5 Handle Rotation Switch
6 Motor Vents
7 Main Handle
8 On/Off Trigger Switch
9 Trigger Lock
10 Brush Access Cover
11 Grinding Guard
12 Disc (not included)
13 Guard Collar
14 Guard Clamp
15 Spindle Lock
16 Pin Spanner
17 Inner Flange
18 Outer Flange
19 Spindle
20 Cutting Wheel Guard

Intended Use

Angle grinder suitable for light to medium duty grinding of metal and other materials with
a fitted disc of the correct type. Suitable for cutting various materials when fitted with the
supplied cutting guard. Also suitable for wire brushing and sanding applications with the
optional purchases of compatible accessories.
Unpacking your Tool
Carefully unpack and inspect your tool. Familiarise yourself with all its features and
functions.
Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool.
Before Use
WARNING: Always unplug the grinder from the mains supply before attempting to fit
or replace any attachment. Never fit any attachment with a maximum speed lower than the
no load speed of the machine.
• All discs and accessories must be subjected to a visual inspection prior to installation, to
ensure they are in good condition and within their expiry date. If in doubt, DO NOT USE
AND DISCARD
• Always check all parts and attachments are secure, and that rotating parts will not foul
on guards or machine case
• Always hold the machine, using both hands, by the handles provided
• Be aware that the cast metal gear housing may get hot during use
• Hot air will be emitted from the ventilation holes
• Ensure that the ventilation holes are not obscured in any way
• Always wear appropriate personal protective equipment for the task. Use of this
machine requires ear defenders, eye protection, gloves, breathing protection, and if
appropriate a hard hat
www.silverlinetools.com
9