Testing And Commissioning; Product Maintenance; Product Disposal; Technical Characteristics Of The Product - Nice GR170 Gebrauchsanleitungen

4

TESTING AND COMMISSIONING

4.1 - Testing
These are the most important phases of automation set-up for ensuring maxi-
mum system safety. The test can also be performed as a periodic check of
automation devices. Testing and commissioning of the automation must be
performed by skilled and qualified personnel, who are responsible for the tests
required to verify the solutions adopted according to the risks present, and for
ensuring observance of all legal provisions, standards and regulations, and in
particular all requirements of the standard 12445, which establishes the test
methods for checking automations for gates and doors.
Additional devices must undergo a specific test for functionality and correct inter-
action with GIRO; therefore, please refer to the instructions manuals of the indi-
vidual devices.
01. Make sure that the provisions contained in chapter 1 "WARNINGS" have
been carefully observed.
02. Check that the joints are in good condition, i.e. there are no breakages.
03. Check that the gearmotor is properly secured to the spring shaft.
04. Check that the screw connections are tightly secured.
05. Check that the electrical contacts are in good condition.
06. Check that the ring nuts do not feature excessive axial play.
07. Check the adjustment of the limit switches by making a complete manoeu-
vre (raise-lower).
08. Check that the gearmotor, locked at any point, does not show any sign of
movement.
09. (only for one way versions) Check that the release easily disengages the
gearmotor from the rolling door.
4.2 - Commissioning
Commissioning can only be performed after positive results of all test phases.
01. Prepare and store for at least 10 years the technical documentation on the
automation, which must at least include: an overall drawing of the auto-
mation, the wiring diagram of all connections made, an assessment of all
risks present and relative solutions adopted, declaration of conformity of
the manufacturer of all the devices used (for Giro use the CE Declaration of
Conformity attached); a copy of the instruction manual and the automation
maintenance schedule.
02. Post a label on the door providing at least the following data: type of auto-
mation, name and address of manufacturer (person responsible for the
"commissioning"), serial number, year of manufacture and "CE" marking.
03. Post a permanent label or sign detailing the operations for the release and
manual manoeuvre near the door.
04. Prepare the declaration of conformity for the automation and deliver it to
the owner.
05. Prepare the "Instructions and warnings for using the automation" manual
and deliver it to the owner.
06. Prepare the maintenance schedule of the automation and deliver it to the
owner (it must contain all the maintenance instructions for the individual
devices).
WARNINGS: • All technical characteristics
stated in this section refer to an ambient
temperature of 20°C (± 5°C). • Nice S.p.a.
reserves the right to apply modifications to
products at any time when deemed neces-
sary, maintaining the same intended use
and functionality.
Note:
- GR170 and GR170/V1 one way ver-
sions
- GR170R reversible versions
3 – English

TECHNICAL CHARACTERISTICS OF THE PRODUCT

MODEL
Power supply / frequency
Current absorption
Power absorption
Max torque
Max lifting force with Ø 200mm
Rolling door shaft standard diameter
Rolling flange diameter
Crown rotation speed (empty)
Operating ambient temperature
Protection rating
Thermal protector
Continuous operation time
Max number of daily manoeuvres
Weight
* 60 mm with adapter supplied - 48 mm with optional adapter
** 220 with provided adapter - 240 with optional adapter
07. Before commissioning the automation, ensure that the owner is adequately
informed in writing of all associated risks and hazards (e.g. on the Instruc-
tions and warnings for using the automation manual).

PRODUCT MAINTENANCE

Scheduled maintenance every 6 months is necessary to keep the safety level con-
stant and to guarantee the maximum duration of the entire automation.
WARNING: – Maintenance operations must be performed in strict com-
pliance with the safety directions provided in this manual and accord-
ing to applicable legislation and standards.
01. Disconnect any electric power supply, including any buffer batteries.
02. Check the state of deterioration of all the materials in the automation sys-
tem, paying special attention to cases of erosion or oxidation of the struc-
tural parts; replace the parts that do not provide sufficient guarantee.
03. Check the state of wear of the moving parts.
04. Reconnect the power supplies and carry out all the tests and checks
included in paragraph "4.1 Testing".

PRODUCT DISPOSAL

This product is an integral part of the automation system it controls
and must be disposed of along with it.
As in installation operations, at the end of the product's lifespan, disposal oper-
ations must be performed by qualified personnel.
The product is made of various types of materials: some of them may be recy-
cled, while others must be scrapped. Find out about recycling and disposal
systems in use in your area for this product category.
Warning! – some parts of the product may contain polluting or hazardous sub-
stances which, if released into the environment, may cause serious damage to
the environment or to human health.
As indicated by the symbol appearing here, the product may
not be disposed of with other household wastes. Separate the
waste into categories for disposal, according to the methods
established by current legislation in your area, or return the
product to the retailer when purchasing a new version.
Warning! – Local legislation may impose heavy fines in the
event of illegal disposal of this product.
GR170 GR170/V1
GR170R
230V / 50Hz 120V / 60Hz
1,9 A
430 W 455 W
170 Nm 170 Nm
170 kg 170 kg
76 mm * 76 mm *
200 mm ** 200 mm **
8 RPM 10 RPM
-20°C ÷ 50°C -20°C ÷ 50°C
IP 20 IP 20
100°C 100°C
4 minutes 40 s on
40 s off
10
(non consecutive) (non consecutive)
7 kg 7 kg
GR340 GR340/V1
230V / 50Hz 120V / 60Hz
4 A 3,3 A
800 W
340 Nm
340 kg
76 mm *
200 mm ** 200 mm **
8 RPM 10 RPM
-20°C ÷ 50°C -20°C ÷ 50°C
IP 20
100°C
4 minutes
10 10
(non consecutive) (non consecutive)
10,5 kg
7,6 A
900 W
340 Nm
340 kg
76 mm *
IP 20
100°C
40 s on
40 s off
10
10,5 kg