Peavey IPR 1600 Bedienungsanleitung Seite 32

Rated Power (2 x 2 ohms)
Rated Power (2 x 4 ohms)
Rated Power (2 x 8 ohms)
Rated Power (1 x 2 ohms)
Rated Power (1 x 4 ohms)
Rated Power (1 x 8 ohms)
Minimum Load Impedance
Maximum RMS Voltage Swing
Frequency Response
T.H.D. (2 x 2 ohms)
T.H.D. (2 x 4 ohms)
T.H.D. (2 x 8 ohms)
Input CMRR
Voltage Gain
Crossover
Crosstalk
Hum and Noise
Slew Rate
Damping Factor (8 ohms)
Input Sensitivity
Input Impedance
Current Draw @ 1/8 power
Current Draw @ 1/3 power
Cooling
Controls
Indicator LEDs
Protection
Connectors
Construction
Dimensions
Net Weight
Gross Weight
Warranty
Rated power readings made with BW: <10 Hz to 22 kHz. All power measurements made at 120 VAC and 240VAC.
2 ohm power is time limited by circuit breaker.
*Net Weight does not include power cord.
IPR-1600 DSP Specification Sheet
- 900 watts per channel @ 1 kHz 1% T.H.D. both channels driven.
- 515 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
- 290 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
- 1050 watts @ 1 kHz at <1% T.H.D.
- 570 watts @ 1 kHz at <0.1% T.H.D.
- 300 watts @ 1 kHz at <0.1% T.H.D.
- 2 ohms.
- 55 volts.
- 10 Hz - 22 kHz, +/- 0.5 dB at 1 watt.
- <0.1% @ 675 watts per channel from 20 Hz to 1 kHz, decreasing to 500 watts at 20 kHz at <0.25%.
- <0.1% @ 510 watts per channel from 20 Hz to 11 kHz, decreasing to 425 watts at 20 kHz at same <0.1%.
- <0.1% @ 270 watts per channel from 20 Hz to 20 kHz.
- > - 69 dB @ 1 kHz.
- x 40 (+32dB).
- Adjustable frequencies with 24dB/oct, 4
- > -70 dB @ 1 kHz at 250 watts power @ 8 ohms.
- > -92 dB, "A" weighted referenced to rated power @ 4 ohms.
- > 12V/μs.
- > 150:1 @ 20 Hz - 1 kHz at 8 ohms.
- 1.14 volts +/- 3% for 1 kHz 4 ohm rated power, 1.07 volts +/- 3% for 1 kHz. 2 ohm rated power.
- 15k ohms, balanced and 7.5k ohms unbalanced.
- 540 watts @ 2 ohms, 350 watts @ 4 ohms, 230 watts @ 8 ohms.
- 1,250 watts @ 2 ohms, 740 watts @ 4 ohms, 450 watts @ 8 ohms.
- Temperature dependent variable speed 80 mm DC fan.
- 2 front panel detented attenuators, push-button navigation encoder to navigate through the menus on the
LCD screen for input mode, parametric EQ, crossover H.P.F, Normal, L.P.F. and more.
- 2 DDT (clip limiting), 2 Signal presence, 2 Active status, 2 Temp and 2 DC protect.
- Thermal, DC, subsonic, incorrect loads, under and over voltage.
- Inputs: Dual Combi 1/4" & XLR, Outputs: Dual 1/4" signal patch, dual twist locking connectors.
- 0.062" thick aluminum.
- 3.5"x19"x 10.5" behind front panel + 0.6" for handle.
- 3.23 kg (7.12 lbs.*)
- 4.31 kg (9.5 lbs.)
- 5 years.
th
order Linkwitz –Riley High Pass and Low Pass filter per channel
32