Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
86
Operation
This chapter gives important operating instructions for
the unit.
NOTE
►
Several buttons can be found on the unit as well as
on the remote control. Identical buttons perform the
same function. The buttons appear in the following
text are the buttons on the unit.
►
The remote control signals are sent to the unit via
infrared light. The transmission of the signals from
the remote control to the unit may be impaired by
direct sunlight on the IR sensor (6).
On/Off
Press the button
/MUT (2) to switch on the set. The
‹
display is activated.
/MUT (2) button to switch the unit
Hold down the
‹
off.
Settings
Volume
WARNING
Hearing damage due to high volume!
High volumes can permanently damage your hearing.
►
Set a moderate volume.
Press the
/ buttons (23) to adjust the volume.
‹
Switch unit to mute
/MUT (2) button to switch the unit to
Press the
‹
mute. MUTE flashes on the display.
Press the
/MUT (2) button again to deactivate the
‹
function.
Sound Settings
Press the
SEL button (5). The current volume is dis-
‹
played. Press the SEL button again to open the next
setting.
The following settings are possible:
VOL - volume (0 to 100)
BAS - bass (-10 to +10)
TRB - treble (-10 to +10)
BAL - Balance (sound distribution between left and
right speakers) (10L to 10R)
FAD - Fader (sound distribution between rear and front
speakers) (10F to 10R)
Press the
/ buttons (23), to change the displayed
‹
setting.
More settings via the SEL button
SEL button (5) pressed for a few seconds to
Keep the
‹
open more settings options. Press the SEL button again
to open the next setting.
Press the
/ buttons (23), to change the displayed
‹
setting.
The following settings are possible:
BEEP
Key tone:
■
BEEP ON:
The unit sounds a beep tone
every time you press a button.
■
BEEP OFF:
The unit sounds no beep tone.
P-VOL
Adjusts the volume at which the unit should
switch on.
AREA
Region, when the unit is used.
Europe (EUR) or USA
NOTE
►
Changing this setting deletes all station
presets.
HOUR
Select the time display here.
24 hour (24 H) or 12 hour (12 H)
NOTE
►
If 12 hours is selected, the display shows:
AM = morning, PM = afternoon.
PCLK
Select here if the time should be displayed
when the unit is switched off.
Radio Reception Settings
PTY button (17) pressed for several seconds
Keep the
‹
to open more setting options. Press the PTY button
again to open the next setting.
Press the
/ buttons (23) to change the displayed
‹
setting.
The following settings are possible:
TA
Traffic announcements
■
TA SEEK:
With activated TA function the
unit searches for a station with traffic an-
nouncements.
■
TA ALARM:
No automatic station search.
The unit sounds a beep tone if no traffic
information is received and NO TP/TA is dis-
played. SEEK PI is displayed if the selected
station does not transmit an RDS signal.
PI
Moving into an area where two stations
with identical AF, but different Pl code (PI =
program information) are received destabilizes
reception. In this situation you have two op-
tions:
■
PI SOUND:
To change stations the other
station is played for less than one second.
■
PI MUTE:
The other station is muted.
RETUNE Delay for automatic search with traffic an-
nouncements and/or program information:
■
S
(Short) after approx. 30 seconds
■
L
(Long) after approx. 90 seconds
Werbung
Kapitel
Fehlerbehebung
