Makita 6911HDA Betriebsanleitung Seite 5

6. Do not store the machine and Battery Car-
tridge in locations where the temperature may
reach or exceed 50°C (122°F).
7. Do not incinerate the Battery Cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Be careful not to drop, shake or strike battery.
9. Do not charge inside a box or container of any
kind. The battery must be placed in a well
ventilated area during charging.
ADDITIONAL SAFETY RULES FOR
MACHINE
1. Be aware that this machine is always in an
operating condition, because it does not have
to be plugged into an electrical outlet.
2. Wear ear protectors.
3. Check the socket carefully for wear, cracks or
damage before installation.
4. Hold the machine firmly.
5. Always be sure you have a firm footing. Be
sure no one is below when using the machine
in high locations.
6. The proper fastening torque may differ
depending upon the kind or size of the bolt.
Check the torque with a torque wrench.
7. When driving into walls, floors or wherever
''live'' electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
TOOL! Hold the machine only by the insulated
grasping surfaces to prevent electric shock if
you drive into a ''live'' wire.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge
(Fig. 1)
• Always switch off the machine before insertion or
removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the
cartridge.
• To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way until
it locks in place with a little click. If not, it may
accidentally fall out of the tool, causing injury to you
or someone around you.
• Do not use force when inserting the battery car-
tridge. If the cartridge does not slide in easily, it is
not being inserted correctly.
Charging
For 6911HDA (Fig. 2)
• Your new battery cartridge is not charged. You will
need to charge it before use. Use the fast charger
Model DC1201 to charge the battery cartridge.
• Plug the fast charger into your power source. The
charging light will flash in green color.
• Insert the battery cartridge so that the plus and
minus terminals on the battery cartridge are on the
same sides as their respective markings on the fast
charger. Insert the cartridge fully into the port so that
it rests on the charger port floor.
• When the battery cartridge is inserted, the charging
light color will change from green to red and charg-
ing will begin. The charging light will remain lit
steadily during charging.
• When charging is completed, the charging light
color will change from red to green and a tone will
sound steadily for about 5 seconds. The charging
time is approximately one hour.
• After charging, unplug the charger from the power
source.
Capacity
Battery type
1222
CAUTION:
• The fast charger Model DC1201 is for charging
Makita battery cartridge. Never use it for other
purposes or for other manufacturer's batteries.
• When you charge a new battery cartridge or a
battery cartridge which has not been used for a long
period of time, it may not accept a full charge. This
is a normal condition and does not indicate a
problem. You can recharge the battery cartridge
fully after discharging it completely and recharging a
couple of times.
• If you charge a battery cartridge from a just-
operated machine or a battery cartridge which has
been left in a location exposed to direct sunlight or
heat for a long time, the charging light may flash in
red color. If this occurs, wait for a while. Charging
will begin after the battery cartridge cools. The
battery cartridge will cool faster if you remove the
battery cartridge from the fast charger.
• If the charging light flashes alternately in green and
red color and a tone sounds ''beep, beep, beep, ...''
for about 20 seconds, a problem exists and charg-
ing is not possible. The terminals on the charger or
battery cartridge are clogged with dust or the battery
cartridge is worn out or damaged.
For 6911HDB (Fig. 3)
• Your new battery cartridge is not charged. You will
need to charge it before use. Use the fast charger
Model DC1411 to charge the battery cartridge.
• Plug the fast charger into your proper source. The
charging light will flash in green color.
• Insert the battery cartridge so that the plus and
minus terminals on the battery cartridge are on the
same sides as their respective markings on the fast
charger. Insert the cartridge fully into the port so that
it rests on the charger port floor.
• When the battery cartridge is inserted, the charging
light color will change from green to red and charg-
ing will begin. The charging light will remain lit
steadily during charging.
Number of
(mAh) cells
2,000 10
5