Specifications - Makita 6911HDA Betriebsanleitung

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 O-ring
5 Socket

SPECIFICATIONS

Model
Capacities
Standard bolt ........................................................... M8 — M14
High tensile bolt ....................................................... M6 — M12
Square drive ............................................................... 12.7 mm
No load speed (RPM) ................................................. 0 — 1,800
Impacts per minute ..................................................... 0 — 2,500
Max. fastening torque ................................................. 1,200 kg . cm
Overall length ............................................................. 221 mm
Net weight ................................................................... 1.8 kg
Output ......................................................................... D.C. 12 V
Charging time ............................................................. Approx. 70 min.
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Safety Hints
For your own safety, please refer to enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
4
Explanation of general view
6 Pin
7 Switch trigger
8 Reversing switch
9 Fastening torque
0 Fastening time
6911HDA
9. Do not operate charger if it has received a
10. Do not disassemble charger or battery car-
11. To reduce risk of electric shock, unplug
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when tem-
2. Do not attempt to use a step-up transformer,
3. Do not allow anything to cover or clog the
4. Always cover the battery terminals with the
5. Do not short the battery cartridge:
q Seconds
w Proper fastening torque for
e Fast charger
r Screw
t Set plate
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
perature is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
an engine generator or DC power receptacle.
charger vents.
battery cover when the battery cartridge is not
used.
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
6911HDB
M8 — M14
M6 — M12
12.7 mm
0 — 1,800
0 — 2,500
1,200 kg . cm
221 mm
1.8 kg
D.C. 12 V
Approx. 65 min.