Fein STS 325 R Gebrauchsanleitung Seite 16

STS 325.book Seite 16 Donnerstag, 16. Juni 2005 9:07 09
EN
Using the clamping device.
The figures showing the different clamping
devices, the saw-blade guide and the free hand
rest can be found at the end of the Instruction
Manual. The numbering of the operating ele-
ments in the following text relates to these fig-
ures.
Clamping the work piece.
Clamping device 9 07 02 001 00 1
For pipes with a diameter of up to 150 mm use
clamping device 9 07 02 001 00 1.
Position the clamping chain (14) around
the work piece and insert the hooks of fish
plate (7) in the clamping chain (14).
Tension the chain using gripping arm (6).
Mount the hacksaw onto the supporting
bolt (20). (see "Mounting the clamping
device")
The clamping head (19) can be adjusted to the
sawing cuts and can be pivoted.
Clamping device 9 07 02 004 00 6
For large pipes with a diameter of 150 mm to
325 mm use the clamping device
9 07 02 004 00 6 and saw blades with a length
of 500 mm or 600 mm and a thickness of 2 mm.
Using the chain extension, larger pipes can also
be machined with a diameter of 440 mm.
Saw-blade guide 9 06 06 002 00 9
For operations using a saw blade with a thick-
ness of 1.6 mm and a length of 530 mm use the
saw-blade guide 9 06 06 002 00 9.
Fasten the saw-blade guide – without the
auxiliary handle mounted – to the drill hole
on the gear head of the pneumatic hack-
saw.
Clamping device 9 07 02 003 00 8
For machining profiled sections with a width of
290 mm and a height of 550 mm, use clamping
device 9 07 02 003 00 8. The design is equiva-
lent to that of a parallel vise. The clamping
jaws (10, 11) and the clamping head (19) are
adjustable.
16
Free hand rest 3 27 14 062 02 3
For sawing materials such as corrugated metal,
for example, use the free hand rest
3 27 14 062 02 3. Disconnect the auxiliary han-
dle and fasten the free hand rest to the stroke
mechanism and in the drill hole on the top of the
gear head.
Clamping device 9 07 02 005 00 0 (without figure)
For cutting pipes and round materials with an
external diameter of 80 mm to 400 mm, use the
clamping/feeding device 9 07 02 005 00 0 as a
guide for the hacksaw. By means of a slipping
coupling, the pressing-on time of the saw blade
is limited and thus the service life is longer. For
handling, see the Instruction Manual
3 41 00 898 06 6.
Mounting the clamping device.
Insert the retaining bolts of the clamping
device into the cross hole on the underside
of the gear housing assembly.
Fasten the clamping device by tightening
the locking pins securely.
General operating instructions.
Check that the pressure in the compressed-air
supply conforms with the pressure given on the
rating plate on the pneumatic hacksaw.
Before connecting, blow through the
hose.
The hose should have a minimum diameter of
13 mm. The opening of the cock and the cou-
pling should be at least 8 mm.
Before commencing work, check that the oil
container is full (see Section, "Repair and Main-
tenance"). Fill the oil container as required, with
FEIN Special Motor Oil 3 21 32 017 05 0 (high-
grade hydraulic oil, type: HLP/ISO-VG:22). Do
not use any vehicle motor oils as they are not
suitable for pneumatic hacksaws.
STS 325