Terminal Diagram Control Unit B; Technical Data - Dorma Rst Montageanleitung

DORMA

6. Terminal diagram control unit B

31 32 33
X13
X1
59
F2
60
F3
58
57
18K
X11
56
X10
A B C
X14
X15
6162 55 54 14
Connection blocks Control board
X1
31 24 V
Secondary side, transformer
12 V
32
0 V
33
X2
1
Power supply to external loads,
1
e.g. electro-mechanical lock (radar
4
detector) 1+2 = 24 VAC, 2+4 = 12 VAC.
4
2
2
Drive unit disabling contact for e.g.
5
smoke detector input; jumper if not used
6
Power supply to external loads,
34 GND
e.g. electro-mechanical lock (max 700mA).
35 24 VDC
max. 1400 mA
X3
36
Primary side, transformer
37
X4
Incoming power supply:
N
38
L1 230 VAC ±10%, 50/60 Hz
39
X5
40 U
Motor
41 V
W
42
43
Capacitor
6µF
44
X6
16
„Door open" limit switch
17
18
Solenoid valve
19
„Door closed" limit switch(cam) Switches off
20
the hinge-side safety sensor (e.g.IRS)
21
X7
OFF (GND)
12
Exit only
45
Permanent open
11
Automatic
13
„Door closed" limit switch (switches off the
46
safety sensor on the opposite hinge-side
jumper if not used.)
47
Electro-mechanical lock:
27 C
Floating contact (change over contact),
26 NO
fixed pulse duration of 1 sec.1 sec.
25 NC
34
RST
37 36 39
35 34 6 5 2 2 4 4 1 1
X3
X2
R26
A B
S1
S2
X9 X8 X7
15 53 52 51 50 7 8 49 48 25 26 27 47
B
Programme switch
L1 N
38
X5
44
43
X4
42 N
41 V
B
40 U
X6
21
20
19

Technical data

18
Power supply:
17
Fuse F2:
16
Fuse F3:
LED: A (V20)
LED: B (V18)
46 13 11 45 12
X8
48
Night-bank activator
49
8
Internal activator
7
X9
50
External activator
51
52
Safety sensor, opposite hinge-side
53
Safety sensor hinge-side active leaf;
15
jumper if not used
14
54
Safety sensor hinge-side inactive leaf
Jumper if not used
55
X10
5 + 2-pin interface block for connection cable
X14
linking two control modules for coordinated
double-leaf operation
Control module B (master/ active leaf)
Controls module A (Slave/ inactive leaf).
X11
Stabelized power supply for smoke detector
(max. 100mA) - not switched off by drive unit
56
disabling contact at terminal 5/6 limit switch
18K 57
cut off input
58
X13
59 Sensoric output test GF
Sensoric output test SF
60
X15
Presence sensor on opposite hinge side of
61
passive leaf
62
R26
Hold open time 0 - 30 sec.
S1
Mode selector:
S2
DIP Schalter Grundeinstellung alle "OFF"
OFF ON
1 Test high active
2 Inactive test GF BS
3 Inactive test GF BGS Active test GF BGS
4 Inactive test SF BS
5 Inactive test SF BGS Active test SF BGS
230 VAC ±10%, 50/60 Hz
T 1,6 A at 24 VAC
T 1,6 A at 12 VAC
Error indicator Steuerung A
Error indicator Steuerung B
A Single-leaf mode
B Double-leaf mode
Motor lock mode
C
OFF ON
test low active
Active test GF BS
Active test SF BS