Basic Settings; Selecting The Emergency Trigger Signal; Selecting The Replay Mode; Setting The Clock Manually - Monacor PA-1120DMT Einbau- Und Bedienungsanleitung

5 Basic Settings

5.1 Selecting the
emergency trigger signal
The type of trigger signal can be selected for re-
mote-controlled retrieval of an emergency mes-
sage via the amplifier [connection "E / M TRIGGER
INPUT" (20)] or via the terminals "EMERGENCY"
on the connection plate (18) .
Note: This selection is exclusively made for the emer-
gency announcement triggered via the connection "E / M
TRIGGER INPUT" or via the terminals "EMERGENCY" .
It will not affect any other announcements .
1) Switch on the amplifier or the basic unit .
2) Press the button MENU (10) . The display (4)
will show:
Mode Set
Time
3) Press the button UP (12) or DN (11) repeatedly
until appears on the lower line of
EM Type
the display .
4) Press the button ENTER (6) .
now appear on the first line of the display;
the lower line will show the current trigger
type setting .
5) Use the button UP or DN to select the trig-
ger type and then press the button ENTER to
confirm:
The message will be repeated as long
Latch
as the trigger signal is available .
The message will be repeated until the
Pulse
button START/ STOP (14) is pressed .
To stay with the current trigger type, cancel the
setting by means of the button MENU .
Note: The menu will be automatically exited after
approx . 30 seconds if no button is pressed .

5.2 Selecting the replay mode

The replay of messages stored on the six main
storage locations usually consists of two steps:
1 . Selecting the message
2 . Starting the (multiple) replay
This applies both to the replay via the buttons
on the insertion module (
to the (remote-controlled) replay via switching
contacts ( ☞ chapter 6 .2 .2) .
For immediate message replay, rearrange the
jumper PLAY MODE SELECTOR (22) . Switch off
the unit prior to rearranging the jumper .
will
EM Type
☞ chapter 6 .2 .1) and
replay after the button START/ STOP (14) or
REPEAT/ STOP (13) was pressed
immediate (multiple) replay when the mes-
sage is selected by means of the buttons
M1 – M6 (15)

5.3 Setting the clock manually

The clock can be manually set if synchronisation
of the integrated clock via the wireless transmitter
is not possible or not desired .
1) Switch on the amplifier or the basic unit .
2) Press the button MENU (10) . The display (4)
will show:
Mode Set
Time
3) Press the button ENTER (6) .
now appear on the first line of the display;
the lower line will show the current weekday
setting .
4) Use the button UP (12) or DN (11) to set the
weekday desired:
Monday
Mon
Tuesday
Tues
Wednesday
Wednes
Thursday
Thurs
Friday
Fri
Saturday
Satur
Sunday
Sun
5) Press the button ENTER .
pear on the first line of the display; the lower
line will show
Hour:
setting .
6) Use the button UP or DN to set the hour and
then press the button ENTER to confirm . The
lower display line will now show
the current minute setting .
7) Use the button UP or DN to set the minute
and then press the button ENTER to confirm .
The display will now show the weekday and
the time set .
When a time signal is received,
appear on the display and the clock will be syn-
chronised .

5.4 Increasing the output level

If required, the output level can be increased by
10 dB: Switch off the unit and then rearrange
the jumper J1 (19) from the position "low" to
the position "hi" .
will
Week Set
will ap-
Time Set
and the current hour
and
Min:
will
DCF77 ON
17