Installation; Functional Description - Makita MLT100 Bedienungsanleitung

INSTALLATION

Positioning table saw
Fig.1
Fig.2
Fig.3
Locate the table saw in a well lit and level area where
you can maintain good footing and balance. It should be
installed in an area that leaves enough room to easily
handle the size of your workpieces. The table saw
should be secured with four screws or bolts to the work
bench or table saw stand using the holes provided in the
bottom of the table saw. When securing the table saw
on the work bench, make sure that there is an opening
in the top of the work bench the same size as the
opening in the bottom of the table saw so the sawdust
can drop through.
If during operation there is any tendency for the table
saw to tip over, slide or move, the work bench or table
saw stand should be secured to the floor.
Storing accessories
Fig.4
Fig.5
Push stick, Triangular rule, blade and wrenches can be
stored on the left side of the base and the rip fence and
miter gauge can be stored at the right side of the base.

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function on
the tool.
Adjusting the depth of cut
Fig.6
The depth of cut may be adjusted by turning the handle.
Turn the handle clockwise to raise the blade or
counterclockwise to lower it.
NOTE:
Use a shallow depth setting when cutting thin
•
materials in order to obtain a cleaner cut.
Adjusting the bevel angle
Fig.7
Loosen the lock lever counterclockwise and turn the
handwheel until the desired angle (0° - 45°) is obtained.
The bevel angle is indicated by the arrow pointer.
After obtaining the desired angle, tighten the lock lever
clockwise to secure the adjustment.
CAUTION:
After adjusting the bevel angle, be sure to tighten
•
the lock lever securely.
Adjusting positive stops
Fig.8
Fig.9
The tool is equipped with positive stops at 90° and 45° to
the table surface. To check and adjust the positive stops,
proceed as follows:
Move the handwheel as far as possible by turning it.
Place a triangular rule on the table and check to see if
the blade is at 90° or 45° to the table surface. If the blade
is at an angle shown in Fig. A, turn the adjusting screws
clockwise; if it is at an angle shown in Fig. B, turn the
adjusting screws counterclockwise to adjust the positive
stops.
After adjusting the positive stops, set the blade at 90° to
the table surface. Then adjust the arrow pointer so that
its right edge is aligned to the 0° graduation.
Fig.10
Switch action
CAUTION:
Remove workpiece from the table.
•
Switch off the tool and then press in the restart
•
button.
Before plugging in the tool, always be sure that the
•
tool is switched off.
Fig.11
CAUTION:
Before operation, make sure that the tool is turned
•
on and off.
To start the tool, press the ON ( I ) button.
To stop it, press the OFF ( O ) button.
Sub table (R)
Fig.12
Fig.13
This tool is provided with the sub table (R) on the right
side of the main table. To use the sub table (R), loosen
two screws on the right side counterclockwise, pull out
the table (R) fully and then tighten the two screws to
secure it.
Sub table (back)
Fig.14
To use the sub table (back), loosen the screws on the left
and right hand sides under the table and pull it out
backwards to the desired length. At the desired length,
tighten the screw securely.
Slide table
Fig.15
CAUTION:
After using slide table, be sure to lock it by moving
•
the locking plate to the vertical position.
This tool is provided with the slide table on the left side.
The slide table slides back and forth. Pivot the locking
plates on the back and front sides to the horizontal
8