Hinweis Beachten Sie die Hinweise und Warnungen in diesem Doku- ment. Diese Betriebsanleitung enthält wichtige Informationen zum SICAM P850/P855. Sie ist Bestandteil des gelieferten Produkts. Angaben zur Konformität Das Produkt entspricht den Bestimmungen der Richtlinie des Rates der Europäischen Gemeinschaften zur Anglei- chung der Rechtsvorschriften der Mitgliedsstaaten über die...
Eingetragene Marken ® SICAM ist eine eingetragene Marke der Siemens AG. Jede nicht autorisierte Verwendung ist unzulässig. Alle anderen Beschreibungen in diesem Dokument bzw. in diesen Informationen können Marken enthal- ten, deren Verwendung durch Dritte für ihre eigenen Zwecke die Rechte des Eigentümers möglicherweise verletzen.
Maßnahmen erforderlich machen können. Es enthält jedoch Hinweise, die Sie zu Ihrer persönlichen Sicher- heit sowie zur Vermeidung von Sachschäden beachten müssen. Die Hinweise sind durch ein Warndreieck her- vorgehoben und je nach Gefährdungsgrad wie folgt dargestellt: SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 7
Beachten Sie alle Hinweise, um Sachschäden zu vermeiden. HINWEIS ist eine wichtige Information über das Produkt, die Handhabung des Produktes oder den jeweiligen Teil der Dokumentation, auf den besonders aufmerksam gemacht werden soll. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 8
Das Betriebsmittel (Gerät, Baugruppe) darf nur für die im Katalog und der technischen Beschreibung vorge- sehenen Einsatzfälle und nur in Verbindung mit von Siemens empfohlenen bzw. zugelassenen Fremdge- räten und -komponenten verwendet werden. Wird das Gerät nicht gemäß dieser Produktinformation benutzt, ist der vorgesehene Schutz beeinträchtigt.
Source Software gemäß den jeweiligen Open-Source- Software-Lizenzbedingungen zu nutzen. Bei Wider- sprüchen zwischen den Open-Source-Software- Lizenzbedingungen und den für das Produkt geltenden Siemens Lizenzbedingungen gelten in Bezug auf die Open Source Software die Open-Source-Software- Lizenzbedingungen vorrangig. Die Open Source Software wird unentgeltlich überlas- sen.
Anwendung SICAM P850/P855-Geräte erfassen in allen Span- nungsebenen der Energienetze Messgrößen gemäß der Norm IEC 61000-4-30. Die Messgrößen können über die Kommunikationsschnittstellen zu einem PC und zur Leittechnik ausgegeben oder auf einem optio- nalen Display angezeigt werden. Außerdem werden beim SICAM P855 Betriebs- und Power Quality-Mess- werte in parametrierbaren Zeitintervallen mit diversen Schreibern (z.B.
LED H2 Default IP Address : 192. 168.0.55 Default Subnet Mask : 255.255 .255.0 Bild8-1 SICAM P850/P855 für Schalttafeleinbau, Displayseite Die Displayseite enthält das Display, 4 darunter ange- ordnete Softkeys F1 bis F4 und 4 LEDs, von denen H1, H2 und ERROR parametrierbar sind.
Seite 14
Strommessung Klemmenblock für Spannungsmessung Klammer für Schalttafeleinbau Bild 8-2 SICAM P850/P855 mit Display, Klemmenseite An den beiden Seitenteilen des Gehäuses sind die Hal- terungen für den Schalttafeleinbau angeordnet. Der Einbau des Gerätes ist im Kapitel 10 beschrieben. SICAM P850/P855, Produktinformation...
Gerät die gewünschten Eingaben durchgeführt. Beim Systemstart wird bei gedrückter Softkey F4 (ca. 3 s) die IP-Adresse auf 192.168.0.55 (Werkseinstel- lung) zurückgesetzt. Diese IP-Adresse ist auch auf der Seitenwand des Gerätes (siehe Bild 8-1) ablesbar. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Die Klemmen sind für Leiterquerschnitte von max. 2,5 mm² ausgelegt. Das Gerät darf während des Betriebes keiner Kon- densation ausgesetzt werden. Das Gerät ist so zu platzieren, dass es keiner direk- ten Sonneneinstrahlung und keinem starken Tempe- raturwechsel ausgesetzt ist. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Kegel ein. Montageplatte Befestigungselement ≥ 1 mm, Stahl Bild 10-1 Schalttafeleinbau Stellen Sie das Befestigungselement waagerecht und schrauben Sie es mit einem Schraubendreher (0,6 mm x 4,5 mm) fest, bis die Rutschkupplung wirk- sam wird. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 18
Der Hutschienen-Clip ist auf eine bestimmte Höhenposition voreingestellt. Zum Ändern hebeln Sie die Entriegelung aus ihrer Führung (kein Spezialwerkzeug erforderlich) und rücken Sie die Entriegelung in die gewünschte Position. Anschließend drücken Sie die Entriegelung wieder in deren Führung. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Bei der elektrischen Installation müssen Sie die natio- nalen und internationalen Vorschriften über das Errich- ten von Starkstromanlagen beachten und einhalten. Vor der Inbetriebnahme des Gerätes müssen Sie alle Anschlüsse auf sachgerechte Ausführung prüfen. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 20
Die Polarität und die Phasenzuordnung an den Messwandlern sind durch Sie zu überprüfen. Siemens empfiehlt, das Gerät mindestens 2 Stunden im Betriebsraum liegen zu lassen, bevor Sie es in Betrieb nehmen, um einen Temperaturausgleich zu schaffen und um Feuchtigkeit sowie Kondensation zu vermeiden.
Seite 21
3. Entfernen Sie die Kunststofffolie von der Batterie. 4. Setzen Sie die Batterie unter Beachtung der auf der Geräteoberseite aufgedruckten Polarität in die Bat- teriefassung ein. 5. Schließen Sie den Batteriefachdeckel. HINWEIS Der Batterieaustausch ist im Kapitel 15 beschrieben. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Die Parametrierung ist im Gerätehandbuch, Bestell- nummer E50417-H1000-C482, beschrieben. Anschlussarten Die folgenden Eingangsbeschaltungen sind Beispiele. SICAM P850/P855 kann bis zu den maximal zulässi- gen Strom- und Spannungswerten (siehe Kapitel 19.1) auch ohne zwischengeschaltete Strom- oder Span- nungswandler angeschlossen werden. Erforderliche Spannungswandler können in Stern- oder Dreieckschaltung betrieben werden.
Die Sekundärspannung am Klemmenblock F (Voltage) darf AC 480 V (AC 347 V bei UL-Bedingungen) nicht über- schreiten. Es können Sachschäden entstehen. Achten Sie darauf, dass die maximal zulässige Span- nung Leiter - Erde (PE) nicht überschritten wird. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Die Sekundärspannung am Klemmenblock F (Voltage) darf AC 480 V (AC 347 V bei UL-Bedingungen) nicht über- schreiten. Es können Sachschäden entstehen. Achten Sie darauf, dass die maximal zulässige Span- nung Leiter - Erde (PE) nicht überschritten wird. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
11.4 Beispiel: 4-Leiternetz, gleiche Belastung 10 A 11.5 Beispiel: 4-Leiternetz, beliebige Belastung für Niederspannungsnetze je 10 A SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 26
11.6 Beispiel: 4-Leiternetz, beliebige Belastung für Hochspannungsnetze je 10 A HINWEIS Außer den in dieser Betriebsanleitung enthaltenen Schaltungsbeispielen sind im Gerätehandbuch SICAM P850/P855, Bestellnummer E50417-H1000- C482, weitere Anschlussbeispiele aufgeführt. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Kapitel 19.4) Die Genauigkeit der Frequenzmessung ist je nach Gerätetyp und Spannung unterschiedlich und liegt zwischen 10 mHz und 40 mHz. Detaillierte Anga- ben sind im Gerätehandbuch SICAM P850/P855 beschrieben. Aufzeichnung im SICAM P855 Die Aufzeichnung von Messgrößen und Ereignissen im SICAM P855 ist im Gerätehandbuch beschrieben.
Ethernet-Schnittstelle (Z) auf der Oberseite: Ethernet-Patch-Kabel mit Steckverbinder (RJ45) GEFAHR Gefahr durch hohe Berührungsspannungen Nichtbeachtung hat Tod oder schwere Körperver- letzung zur Folge. Die Erdung müssen Sie am Gerät immer an der Schutzleiterklemme (Klemmenblock H) anschließen. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Das Gerät wird im abgeglichenen Zustand ausgeliefert und braucht während der gesamten Betriebsdauer nicht erneut abgeglichen zu werden. Der Abgleich erfolgt ausschließlich bei betriebsinternem Bedarf. Eine ausführliche Beschreibung des Geräteabgleichs finden Sie im Gerätehandbuch des SICAM P850/P855, Bestellnummer E50417-H1000-C482. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Versuchen Sie nicht, die Batterie zu öffnen. Werfen Sie die Batterie nicht in das Feuer. Setzen Sie die Batterie keinen Temperaturen über 100 °C aus. Versuchen Sie nicht, die Batterie aufzuladen. Verhindern Sie den Zugriff von Kindern auf die Lithium-Batterie. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 33
Seite. 4. Entnehmen Sie die neue Batterie des Typs PANASONIC CR2032 oder VARTA 6032 101 501 der Verpackung (auf der Verpackung aufgedrucktes Verbrauchsdatum beachten). 5. Setzen Sie die Batterie vorsichtig unter Beachtung SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Werfen Sie die Batterie nicht in den Abfall. Bei der Entsorgung der Batterie sind die nationalen und internationalen Bestimmungen einzuhalten. LED-Meldungen SICAM P850/P855 überwacht automatisch die Funk- tionen seiner Hardware-/Firmware-Komponenten. LEDs signalisieren den aktuellen Gerätezustand. HINWEIS Die Bezeichnungen und Funktionen der LEDs auf der Oberseite (siehe Bild 16-1) und auf der Displayseite (siehe Bild 8-1) des Gehäuses sind identisch.
Ethernet Link vorhanden blinkt: Ethernet Link vorhanden, Datentransfer aus: keine Ethernet-Partner angeschlossen LEDs Bedeutung Gerät ausgeschaltet ERROR Keine Firmware geladen ERROR Boot-Programm Softkey F4 wurde während des ERROR Einschaltens der Versorgungsspannung gedrückt (Aufruf Default-IP-Adresse). SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 36
Empfang der IP-Adresse über DHCP) ERROR Default-IP-Adresse wurde mittels Drücken der Softkey F4 übernommen. Boot-Programm wurde gestartet, weil ERROR Fehler in der Prozessapplikation auftrat. DHCP aktiv (H1 schaltet aus nach ERROR Empfang der IP-Adresse über DHCP) SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 37
Nutzung der parametrierten IP-Adresse oder IP-Adresse über DHCP bezogen. DHCP (LED RUN (grün) leuchtet, nachdem ERROR ERROR IP-Adresse von DHCP-Server empfangen). Default-IP-Adresse wurde mittels Drücken ERROR der Softkey F4 übernommen. Doppelte IP-Adresse wurde erkannt. ERROR ERROR SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
-40 °C bis +70 °C. Die relative Luft- feuchte darf weder zur Kondenswasser- noch zur Eis- bildung führen. Siemens empfiehlt Ihnen, bei der Lagerung einen ein- geschränkten Temperaturbereich zwischen +10 °C und +35 °C einzuhalten, um einer vorzeitigen Alterung der eingesetzten Elektrolytkondensatoren vorzubeugen.
Transportanforderungen entsprechend ISO 2248 sichergestellt werden. Eine Lagerverpackung der Ein- zelgeräte ist für den Transport nicht ausreichend. Technische Daten (Auswahl) HINWEIS Weitere Angaben zu den technischen Daten sind im Gerätehandbuch SICAM P850/P855 enthalten. 19.1 Eingänge Eingänge für Wechselspannungsmessungen Nenneingangsspannungen 63,5 V (L-N/PE)
Seite 40
42,5 Hz bis 69 Hz 19.2 Ausgänge Binärausgänge maximale AC-Schaltspannung 230 V maximale DC-Schaltspannung 250 V maximaler kontinuierl. Kontaktstrom 100 mA maximaler Pulsstrom für 0,1 s 300 mA 35 Ω Innenwiderstand zulässige Schaltfrequenz 10 Hz SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 41
Spannungsmagnitude ± 1 % Flicker < 0,1 % Unsymmetrie (alle Kanäle) 100 % ± 0,5 % von U Harmonische 0 % bis 3 % von U Interharmonische 0 % bis 0,5 % von U SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
DC 24 V bis 250 V Netzfrequenz 50 Hz/60 Hz Zulässige Eingangsspan- ±20 % nungstoleranz (gilt für alle Eingangsspannungen) Zulässige höhere Ober- 2 kHz schwingungen bei AC 115 V bzw. AC 230 V Max. Leistungsaufnahme 3 W/6 VA SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Typ T1.6A/250V gemäß IEC 60127 Interne Sicherung, sekundär nicht austauschbar Typ F2A/125V gemäß UL 248-14 19.11 Schutzklasse gemäß IEC 60529 Hutschienengehäuse IP20 Schalttafeleinbaugerät mit Display, ohne Tür IP40 mit Display und Tür IP51 SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Abmessungen (B x H x T) 96 mm x 96 mm x 100 mm 102,9 95,5 Maßangaben in mm Bild 19-1 Abmessungen SICAM P850/P855 mit Display, ohne Tür Weitere Maßbilder finden Sie im Gerätehandbuch. SICAM P850/P855, Produktinformation E50417-B1050-C482-A3, Ausgabestand 03.2013...
Seite 45
Power Monitoring Device and Power Quality Recorder SICAM P850/P855 7KG85xx Product Information E50417-B1050-C482-A3...
Seite 46
Observe the Notes and Warnings for your own safety in this document. This Product Information contains important information about the SICAM P850/P855 and is part of the product delivery. Statement of Conformity This product complies with the directive of the Council of the...
Seite 47
10 Mounting and Commissioning 11 Connection Types 12 Measurands and Recording 13 Interfaces 14 Calibration 15 Replacing the Battery 16 LED Indications 17 Troubleshooting, Repair, Cleaning 18 Storage and Transport 19 Technical Data (Selection) SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Although Siemens AG has made best efforts to keep the document as precise and up-to-date as possible, Siemens AG shall not assume any liability for defects and damage which result through use of the information contained herein.
Registered Trademarks ® SICAM is a registered trademark of Siemens AG. An unauthorized use is illegal. All other designations in this document can be trademarks whose use by third parties for their own purposes can infringe the rights of the owner.
Chapter 1. If you have any questions about the device, please con- tact our Siemens sales partner responsible in your region. Our Energy Customer Support Center is available to you twenty-four hours a day.
Seite 51
Follow all advice instructions to prevent damage to property. NOTE is important information about the product, the handling of the product, or the part of the documentation in question to which special attention must be paid SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 52
Even after the supply voltage has been discon- nected, hazardous voltages can still be present in the equipment (capacitor storage). Equipment with current transformer circuits must not SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
IEC 60417-5032 Direct and alternating current IEC 60417-5033 Three-phase alternating current Earth (ground) terminal IEC 60417-5017 Protective conductor terminal IEC 60417-5019 Caution, risk of electric shock Caution, risk of danger ISO 7000-0434 SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
License Conditions provide for it you can order the source code of the Open Source Software from your Siemens sales contact - against payment of the ship- ping and handling charges - for a period of at least 3 years since purchase of the Product. We are liable for...
IP40 (Position 7 = 1) IP51 (Position 7 = 1) Ethernet Interface and Communication Protocol, RJ45 Modbus TCP IEC 61850 server and Modbus TCP Optional accessories are listed in the device manual. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Application SICAM P850/P855 devices acquire measurands at all voltage levels of power systems according to the IEC 61000-4-30 standard. The communication inter- faces enable the measurands to be forwarded to a PC and to the control center or to be displayed on an optional display.
Default IP Address : 192. 168.0.55 Default Subnet Mask : 255.255 .255.0 Figure 8-1 SICAM P850/P855 for Panel Flush Mounting The display side contains the display, the 4 softkeys F1 to F4 below the display and 4 LEDs of which H1, H2 and ERROR can be parameterized.
Seite 58
Terminal block for Clip for voltage measurement panel flush mounting Figure 8-2 SICAM P850/P855 with Display, Terminal Side The clips for panel flush mounting are on both side walls of the housing. Chapter 10 describes the installa- tion of the device.
When holding softkey F4 down (approx. 3 s) during sys- tem start, the IP address is reset to 192.168.0.55 (default). This IP address is also imprinted on the side wall of the device (see Figure 8-1). SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
2.5 mm² max. (AWG 14). The device must not be exposed to condensation during operation. The device must be installed in a location where it is not exposed to direct sunlight and strong temperature variations. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 61
Figure 10-1 Panel Flush Mounting Move the mounting element to the position. Use a screw driver (0.6 mm x 4.5 mm) to fix the mounting elements until the slipping clutch takes effect. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 62
You can change this position if necessary. To do so, lever the release device out of its guiding (no special tool required) and move the release device into the desired position. Subsequently, press the release device back into its guiding. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
IEC) fuse holder has to be used. NOTE When performing electrical installations, you have to observe the national and international regulations on the erection of electrical power installations. Before commissioning the device, check that all SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 64
The delivery includes a lithium battery that powers the battery-buffered memory and the real-time clock. Upon delivery the battery is insulated in the battery compartment of the device. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 65
3. Remove the insulation from the battery. 4. Insert the battery with the polarity indicated on the cover of the battery compartment. 5. Close the cover. NOTE Chapter 15 describes how to replace the battery. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Connection Types The following input wiring diagrams are examples. Up to the maximum allowable current and voltage values (see Chapter 19.1) SICAM P850/P855 can also be connected without interconnected current and voltage transformers. Required voltage transformers can be operated in star connection or delta connection.
Seite 67
AC 480 V (AC 347 V for UL condi- tions). This could cause material damage. Please make sure that the maximum permissible voltage on conductor - ground (PE) is not exceeded. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 68
AC 480 V (AC 347 V for UL condi- tions This could cause material damage. Please make sure that the maximum permissible voltage on conductor - ground (PE) is not exceeded. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 69
11.4 Example: 4-wire System, Balanced 10 A 11.5 Example: 4-wire System, Unbalanced for low-voltage power systems resp. 10 A SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 70
Example: 4-wire System, Unbalanced for high-voltage power systems resp. 10 A NOTE The SICAM P850/P855 device manual, order number E50417-H1040-C482, provides more circuit examples in addition to the ones shown in these operating instructions. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Acc. to class S, IEC 61000-4-30: a-b, b-c, c-a (only SICAM P855) Pst: ±10 % Plt: ±10 % Pinst: ±16 % Active energy WP demand a, b, c, Σ ±0.5 % SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 72
The accuracy of the frequency measurement dif- fers according to device type and voltage and ranges between 10 mHz and 40 mHz. The SICAM P850/P855 device manual provides detailed information. Recording in SICAM P855 The device manual provides a detailed description of recording measurands and events.
Danger due to high voltages Non-observance will lead to death or serious injury. The grounding on the device always has to be con- nected to the protective conductor terminal (termi- nal block H). SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Terminal assignment Table 13-1 Terminal assignment SICAM P850/P855 Connection Function Description Conductor a, input, => E: I current measurement Conductor a, output, <= E: I current measurement Conductor b, input, => E: I current measurement Conductor b, output, <= E: I...
The calibration is only carried out if necessary due to internal requirements. For a detailed description of the device calibration, see the device manual of SICAM P850/P855, order number E50417-H1040-C482. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
This message can also be parameterized on one of the 3 LEDs H1/H2/ ERROR or switched to one of the binary outputs (see Device Manual SICAM P850/P855, order number E50417-H1040-C482). WARNING Warning of incorrect treatment of the lithium battery (type PANASONIC CR2032 or VARTA 6032 101 501) or the use of an incorrect battery type.
Seite 77
4. Remove the new battery type PANASONIC CR2032 or VARTA 6032 101 501 from the packaging (check the expiry date on the packaging) 5. Insert the battery carefully into the battery compartment with the polarity indicated above the SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
The national and international regulations must be observed when disposing of the battery. LED Indications SICAM P850/P855 automatically monitors the functions of its hardware and firmware components. The LEDs indicate the current device status. NOTE The designations and functions of the LEDs on the upper side (see Figure 16-1) and on the display side (see Figure 8-1) of the housing are identical.
Ethernet partners connected LEDs Meaning Device switched off ERROR No firmware loaded ERROR Boot loader Softkey F4 was pressed while switching on ERROR the supply voltage (activation of the default IP address). SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 80
The default IP address was applied by pressing softkey F4. Boot loader was started because an error ERROR occurred in the process application. DHCP active (H1 switches off after ERROR reception of the IP address via DHCP) SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 81
DHCP (LED RUN (green) is lit after the IP ERROR ERROR address was received by the DHCP server). The default IP address was applied by ERROR pressing softkey F4. Double IP address detected. ERROR ERROR SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Furthermore, hazardous voltages can lead to lethal injuries when the work is performed improperly. If you suspect that the device has a defect, Siemens recommends to send the entire device back to the manufacturer. If possible, use the original transport packaging or an equivalent packaging.
63.5 V (ph-N/PE) 110 V 230 V 400 V (347 V for UL conditions) Maximum measurement voltage ph-N/PE 480 V (347 V for UL conditions) ph-ph 831 V (600 V for UL conditions) SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 84
Maximum AC contact voltage 230 V Maximum DC contact voltage 250 V Maximum cont. contact current 100 mA Maximum pulse current for 0.1 s 300 mA 35 Ω Internal impedance Admissible contact frequency 10 Hz SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 85
± 1 % Flicker < 0.1 % Unbalance (all channels) 100 % ± 0.5 % of U Harmonics 0 % to 3 % of U Interharmonics 0 % to 0.5 % of U SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
50 Hz/60 Hz Admissible input voltage ±20 % tolerance (applies to all input voltages) Admissible higher harmonics 2 kHz at AC 115 V or AC 230 V Maximum power consumption 3 W/6 VA SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 87
F2A/125V acc. to UL 248-14 19.11 Protection class according to IEC 60529 DIN rail side IP20 Panel flush mounting device with display, without door IP40 with display and door IP51 SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...
Seite 88
3.78 inches x 3.78 inches x 3.94 inches 102.9 (4.05) 8.5 (0.85) 95.5 (3.76) Dimensions in mm (inch) Figure 19-1 Dimensions SICAM P850/P855 with Display, without Door Further dimension drawings are provided in the device. manual. SICAM P850/P855 7KG85xx, Product Information E50417-B1050-C482-A3, Edition 03.2013...