Ironing With Steam; Ironing Without Steam; Shot Of Steam - Siemens sensorSteam TS12 Serie Gebrauchsanleitung

After the initial 1 minute period:
• "eco" setting is automatically selected.
• The green lamp (5) stops lashing.
• The "activeControl Plus" indicator lamp (3) (clear
light) goes on and starts lashing.
From this moment on, when the handle (1) of the
iron is gripped or if the steam activation button (2)
is pressed at steam setting:
• The "activeControl Plus" indicator lamp (3) stops
lashing.
• The pump starts working and steam is generated
automatically.
If the handle (1) is released:
• Steam generation will stop.
• The "activeControl Plus" indicator lamp (3) will lash
• The iron shuts off automatically. If the handle is
gripped again, the iron turns on.
If the iron remains plugged in and is not used for
several minutes:
• After the handle (1) is touched or the steam activation
button (2) is pushed again, the green light starts
lashing.
• Steam generation will not be possible for several
seconds, until the appropriate working temperature
has been reached.

Ironing with steam

The steam control is used to adjust the amount
of steam produced when ironing (see "setting the
steam amount" section).
Steam can be generated in two ways :
1. Continuous steam generation :
• Set the steam control to "eco" or "max" position.
• Grip the handle (1).
2. Steam on demand :
• Set the steam control to the "
continuous steam generation while gripping the handle
(1). On this setting, steam can only be produced
when manually pressing the steam activation button
(2) under the handle.
• Press the steam activation button (2).
Important :
• Steam is only available if the temperature control (15)
is set at the steam symbols
"max".
• Adjust the temperature setting and then set the
steam control according to the table below. Steam
will automatically be produced:
Temperature control (15) setting
••
••• to "max"
Note: Once a steam ironing setting has been chosen
using the temperature control (15), steam generation
may be delayed for several seconds until the appropriate
working temperature has been reached.

Ironing without steam

This enables the iron to be used for dry ironing.
• Grip the handle (1) and set the steam control to the
• The temperature control (15) adjusts the temperature
• While ironing, do not press the steam activation
Spray
This can be used to remove stubborn wrinkles.
• Do not use the spray function with silk as staining
• When ironing, press the spray button (7) and water will

Shot of steam

(4)
This can be used to remove stubborn wrinkles or to
press in a sharp crease or pleat. It cannot be used
on a synthetic setting for delicate items.
• Set the temperature control (15) to the "•••" or "max"
• Set the steam control to the "max" position.
• Press the shot of steam button (6) on the handle
Vertical steaming
" position, to cancel
This can be used to remove creases from hanging
clothes, curtains etc.
Do not iron clothing while it is being worn!
Never spray or aim the steam at persons or
animals!
• Set the temperature control (15) to the "•••" or "max"
- between "••" and
• Hold the iron in an upright position about 15 cm away
• Press the steam activation button (2). The shot of
Steam setting
eco
max
setting.
of the soleplate (13). Set it to the corresponding
position by lining it up with the temperature index (14)
on the iron.
Select an appropriate temperature for the type of
material being ironed (see "setting the temperature"
section).
button (2).
may occur.
spray out of the spray nozzle (10) onto the garment.
position.
repeatedly at intervals of 5 seconds.
Warning!
position and the steam control to the
from the garment being steamed.
steam button (6) on the handle may be additionally
pressed at intervals of 5 seconds. However, after
4 shots of steam, wait for 10 seconds to allow for
continued steam production.
(5)
(6)
(7)
(8)
position.