Brief Description Of The Press Device - NovoPress ACO203 BT Betriebsanleitung

The stated vibration emission value can also be used to obtain an initial estimate of interruptions
during intermittent operation.
Caution The vibration emission value may differ from the stated value while the device is actually in
use, depending upon the manner in which the device is used. It may be necessary to establish safety
measures to protect operating personnel, depending on the actual conditions of use (intermittent
operation.
Pos : 31 /RVT/T echnisc he Daten/Ladeger ät @ 0\mod_1381215657501_18.doc x @ 1310 @ @ 1
Battery charger
For information on the function and operation of the battery charger and the rechargeable batteries,
please consult the battery charger operating instructions.
Pos : 32 /RVT/Kurz bes chr eibung/Entlastungs knopf/Pr ess automati k/ACO/EC O/202/203 @ 1\mod_1424269079338_18.doc x @ 9192 @ 12 @ 1
7

Brief description of the press device

7.1 Automatic press cycle (Fig. 1)
The device features an automatic press cycle. This ensures that the pressing operation is always
completed. The automatic press cycle is activated after approx. 1.5 seconds. After the automatic press
cycle has been triggered, the green LED (2) goes out and the pressing operation runs automatically.
The pressing operation can then only be stopped by pressing and holding release button (5). After the
pressing operation has been completed, the motor automatically switches off and the green LED (2)
lights up again.
If the start button (1) is released before the automatic press cycle begins, the piston in the press
device moves back to its starting position. The pressing operation will not have been completed. The
pressing operation must be triggered again.
Pos : 33 /RVT/Kurz bes chr eibung/Entlastungs knopf/AC O102, ACO152, AC O/ECO202, AC O202XL @ 0\mod_1382425726244_18.doc x @ 1401 @ 2 @ 1
7.2 Release button (Fig. 1)
The pressing operation can be stopped at any time by pressing and holding the release button (5).
The piston in the press device then returns to its starting position.
Pos : 34 /RVT/Kurz bes chr eibung/Pressstellenbel euc htung/AC O/EC O203 @ 4\mod_1495001319180_18.doc x @ 31153 @ 2 @ 1
7.3 Pressing point lighting
When the start button (1) is pressed, the pressing point is lit by 2 LEDs (12). If the press device is out
of use for a longer period, the device and the LEDs switch off.
Pos : 35 /RVT/Kurz bes chr eibung/F unksc hni ttstelle/Funks chnittstell e - allgemei n - Gerätenamen 3 @ 5\mod_1519291628348_18.doc x @ 34933 @ 2 @ 1
7.4 Wireless interface (only ACO203 BT)(Fig. 1)
The ACO203 BT device features a wireless interface if it shows the following characteristic:
• Blue LED (10)
This wireless interface together with the NovoCheck app can be used to connect the ACO203 BT to a
mobile terminal device, such as a smartphone, tablet, etc. (Android, IOS; further information at
www.novopress.de). The following functions are available:
• Reading the press device
• Checking the press device
• Making settings
• Generating construction site reports.
To establish a connection, the press device must be operational and the NovoCheck app installed on
the terminal device.
The press device can now be connected with the NovoCheck app. (For more information, go to
www.novopress.de) When the connection to the wireless interface was established successfully, the
blue LED (10) lights up.
The blue LED (10) goes out if no connection has been established until the first pressing operation is
performed. A new attempt to establish the connection can only be made if the press device has been
switched off in the meantime. It may be necessary to pull the rechargeable battery for this.
If you do not wish to establish a connection, press the start button (1) once again and perform the
pressing operation.
Pos : 36 /RVT/Allgemeines /#### Seitenumbr uch #### @ 0\mod_1380200837280_0.doc x @ 885 @ @ 1
ACO203 / ACO203 BT / ECO203
17
EN