Operation - HQ Power VDPL100WL Bedienungsanleitung

c) Gene eral
• Ma ke sure there is
coo oling.
• Hav ve a qualified e
• Co nnect the devic
• The e installation ha
7. Op eration
Refer to t the illustrations
• Inser rt the power plu
main s.
• The V VDPL110WLca
mod e.
Automa atic mode
• Set t DIP switch 1 [
• Set t DIP switch 2 [
• Set t DIP switch 3 [
• Set t DIP switch 4 [
No ote: only the hig
Slave m mode
• Co nnect multiple V
• Set t DIP switches 1
DMX co ontrolled mo
• Set t DIP switch 10
• All DMX-controlled
sig nals. This digita
the e DMX controller
ind dividual address
• Wh hen all devices h
par rticular channel
sim multaneously. If
num mber. Changing
• In case of the 2-ch
(CH H1~2), the seco
• Use e the DIP switch
• Ref fer to the table
Ch hannel DMX-5
CH1 000
000
064
CH2
128
192
8. Cle eaning and
• All sc crews should be
• The h housing, the len
truss sing) should not
supp orts, do not cha
• Mech hanically moving
• The e electric power s
the d device.
10.01.20 011
s no flammable material within
lectrician carry out the electric
e to the mains w with the power
as to be approve ed by an expert
s on page 2 of th his manual.
ug into the powe er input [4]. Ins
an operate in thr ree modes: aut
[1] to ON to ena able both water
[1] to ON to fre eze the water e
[1] to ON to fre eze the colour.
[1] to ON to fre eze both colour
ghest DIP switch h takes effect.
VDPL110WL's as described in
1 and 10 [1] to ON to enable s
de
[1] to the ON position to enab
d devices need a a digital start ad
al start address is the channel n
r. The same sta arting address ca
can be set for every device.
have the same a address, all the
. In other words s: changing the
you set individ ual addresses, e
g the settings of f one channel w
hannel VDPL11 10WL, you will
ond unit to 3 (1 + 2) (CH3~4),
hes [1] to set t he appropriate
switch
value
below for an ov verview of the c
512 value Fu nction
0 ~ 255 dim mmer: 0% ~ 10
0 ~ 063 wa ter effect enabl
4 ~ 127 wa ter effect fixed
8 ~ 191 wa ter effect enabl
2 ~ 255 wa ter effect fixed
maintenan nce
e tight and free of corrosion.
nses, the mount ting supports an
t be deformed, m modified or tam
ange the locatio on of the connec
g parts must no t show any sign
upply cables mu ust not show an
VDPL11 10WL
a 50cm radius
al connection.
plug. Don't con
t before the dev
sert the other e
tomatic mode,
r effect and colo
effect. The colou
The water effec
r and water effe
§6.b.
slave mode.
ble DMX control
ddress so that t
number from w
an be used for a
units will "listen
settings of one
each device will
will only affect th
have to set the
the third to 5 (
DMX address.
1 2 2 3 4
1 2 2 4 8
ontrol signals p
00%
ed+ colour cha
+ colour chang
ed + colour fixe
+ colour fixed
nd the installatio
mpered with e.g.
ctions ...
ns of wear and t
ny damage. Hav
5
of the device an nd there is suffi
nect it to a dim ming pack.
vice is taken into o service.
end of the powe r cable into the
slave mode o or DMX control
our changing.
ur still changes.
ct is still active.
ect.
led mode.
he correct devic ce responds to t
hich the device starts to "listen
a whole group o of devices or an
n" to the contro ol signal on one
e channel will af ffect all devices
"listen" to a se eparate channel
he device in que estion.
start address o of the first unit t
(3 + 2) (CH5~6 6), and so on.
5 5 6 7 8 8 9
1 6 32 64 12 28 256
er channel.
nging
ing
ed
on location (e.g . ceiling, suspen
do not drill ext tra holes in mou
tear.
ve a qualified te chnician mainta
cient
led
the
n" to
to 1
nsion,
unting
ain
man nv
©Vellem