Bosch GWS Professional 18V-10 C Originalbetriebsanleitung Seite 27

Noise emission values determined according to EN 60745-2-3.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K determined according to EN 60745-2-3:
h
Grinding surfaces (roughing):
a
h
K
Grinding with abrasive disc:
a
h
K
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting
Using the GCY 30-4 Bluetooth
Module
®
Note: The GCY 30-4 Bluetooth Low Energy Module is avail-
able as an accessory with GWS 18V-10 C power tools; it is
included in the scope of delivery for GWS 18V-10 SC power
tools.
Read the corresponding operating instructions for informa-
tion about the GCY 30-4 Bluetooth
Bosch Power Tools
GWS 18V-10
3 601 JG3 3...
dB(A)
dB(A)
dB
2
m/s
2
m/s
2
m/s
2
m/s
Charging the Battery
u
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Follow the instructions on correct disposal.
Removing the battery
The battery (8) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (9) unintentionally. As long as the battery is in-
®
Low Energy
serted in the power tool, it is held in position by means of a
spring.
®
Low Energy Module.
GWS 18V-10 GWS 18V-10
SC SC
3 601 JG3 6.. 3 601 JG3 4..
79 79
90 90
3 3
6.0 6.0
1.5 1.5
3.5 3.5
1.5 1.5
Use only the chargers listed on the accessories page.
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 4B1 | (09.05.2018)
English | 27
GWS 18V-10
SC SC
3 601 JG3 5..
79 81
90 92
3 3
6.0 6.5
1.5 1.5
3.5 3.0
1.5 1.5