Operation - ratiotec rapidcount S Bedienungsanleitung

Operation

right
wrong
12
1. Connect the power cable and switch on the machine.
The machine now carries out a self-test sequence.
A "0" appears on the display. Should a different symbol
appear, please refer how to proceed under "Trouble-
shooting".
2. To avoid error messages and damages to the sensors,
any severely damaged and dirty bank notes should be
sorted out now.
3. Set the bank-note feeder to the width of the bank notes
to be counted.
4.
Slightly fan out the bank notes as shown in the figure.
Lay a pre-sorted stack of bank notes (e.g. only 20 Euro
bank notes) in the bank-note feeder. The machine starts
the counting process automatically and shows the
counted piece number on the display. If the total-value
count mode is activated on rapidcount S 85 then bank
notes can be placed unsorted (mixed) on the banknote
feeder. The machine shows the total value of the notes.
If total-value count mode is deactivated, the piece
number will be displayed. The S60 model detects smal-
ler bank notes if IR or MG detection is activated (up to
100 Euro) in a stack. The first bank note that is drawn in
is always used as reference. Whenever a smaller bank
note is detected, the machine stops automatically (Er-
ror "Ed"). The S 85 model detects smaller and larger
bank notes in a stack whenever authenticity detection
and total-value count are activated. The first bank note
that is drawn in is used as reference. If a bank note with
a different format is detected the machine stops auto-
matically (Error "F-P").
5. The sensitivity DEN should always stand on 2 in the
case of Euro bank notes. (factory setting)
Functions
Counterfeit money detection (only rapidcount S 60 / 85)
The counterfeit money detection is already set for the Euro,
ex-factory. You can activate or deactivate individual detec-
tion features of S 60 separately with the buttons IR (in-
frared), UV (ultraviolet) and MG (magnetic). You can activate
or deactivate the authenticity detection features of the S 85
all together with the CD button (Counterfeit Detection).The
detection is active if the respective button illuminates. Upon
detection of a fake or suspect bank note, the machine stops
and a corresponding error message is displayed (see error
massages on the display).
Batch function
You activate the batch / stack function using the BAT but-
ton. Whenever you press the button, default values change
as follows: 100/50/20/10/5. If you wish to count a different
piece number of bank notes, use the button "+1" in order
to increase the default value step-by-step. If you hold the
"+1" button pressed, the value increases in quick mode up
to maximum 999. The machine stops as soon as the default
piece number is reached. After removing the bank notes,
the machine automatically starts a new counting process if
some bank notes still lie in the bank-note feeder.
The batching / stacking function is deactivated by pressing
the CE button.
Adding function
With this function, it is possible to add several counting
processes. If this function is activated then the counter is
not reset to "0" after removing the money. In the display
the overall piece number of all counted bank notes is displa-
yed (S 20 and S 60 up to max. 999 pieces; S 85 up to max.
60.00 pieces of total-value display max. 99,999). To reset
the counter again to "0," press CE.
Report function
With this function, you can have the counting result displa-
yed in detail.Using the button "REP," the piece number and
the total-value of individual bank note types can be displa-
yed. On the right side of the display, the type of bank note
to be displayed is seen. First, the piece number appears and
then the total value of the respective type of bank note.
Print function (only S 85)
By pressing the "P" button, the counting report is printed
out on the printer.
13