Fan Only; Adjusting The Fan Speed; Night Mode; Setting The Timer - Technibel MRAF98C5T Serie Bedienungsanleitung

NOTE
Use DRY operation when you want to reduce the humidity
●
in the room.
● Once the room temperature reaches the set level, the unit
repeats the cycle of turning on and off automatically.
During DRY operation, the fan speed is automatically set
●
to or stops to prevent overcooling.
Dry operation is not possible if the indoor temperature is
●
15 °C or less.

FAN ONLY

If you want to make air circulate without any temperature control,
follow these steps:
1. Press the ON/OFF operation button and switch the air
conditioner ON.
2. Press MODE button until only the
the display.

ADJUSTING THE FAN SPEED

AUTOMATIC
Simply set the FAN selector to the
microcomputer automatically controls the fan speed when
the AUTO mode is selected. When the air conditioner starts
operating, the difference between the room temperature
and the set temperature is detected by the microcomputer
which then automatically switches the fan speed to the
most suitable level.
WHEN DIFFERENCE BETWEEN
ROOM TEMPERATURE AND SET
TEMPERATURE IS
Cooling and 2 °C and over
dehumidifying Between 2 and 1 °C
modes: Below 1 °C
2 °C and over
Heating mode:
Below 2 °C
NOTE
The above mentioned data make reference to the air
conditioner operating when the sensor on the remote control
unit is ON. (Refer to temperature sensor selector). If the
sensor on the indoor unit is being used then actual operation
will slightly differ from that described in the above tables.
The automatic speed is not available in FAN ONLY mode.
MANUAL
If you want to manually adjust speed just set the FAN selector
as desired.
High speed Med. speed

NIGHT MODE

The NIGHT mode enables you to save energy.
●
1. Set the MODE selector to cool, dry or heat.
2. Press the NIGHT button.
3. The mark appears on the display. Press the NIGHT
button again to release the NIGHT function.
What does the NIGHT mode mean?
In this mode, the air conditioner will cool or heat the room to the
set temperature, and then the thermostat will make the unit pause.
After about 1 hour, the air conditioner will automatically reset the
set temperature as follows (also refer to graphs).
Cooling and Dehumidifying
When the room temperature reaches the new set value,
the thermostat will cause the unit to pause. After about 1
hour the temperature will be raised by 1 °C in cooling, or
lowered by 1 °C in heating. This enables you to save energy
without sacrificing your comfort.
COOLING AND DEHUMIDIFYING
Setting temperature Room temperature
fan sign appears on
position.A

SETTING THE TIMER

A) HOW TO SET THE ON TIME
1. Press the SEL TYPE button once.
The ON and time indications flash.
2. Press the SET H button until the
designed hour is displayed.
Press the SET M button until the
designed minutes are displayed. The
FAN SPEED
display will change automatically back
to show the present time after 10 sec.
3. Press the ON/OFF button to start the air
High
conditioner.
Medium
4. Press the TIMER SEL button to activate
Low
the ON timer.
High
B) HOW TO SET THE OFF TIME
Medium
1. Press the SEL TYPE button twice.
The OFF and time indications flash.
2. Press the SET H button until the
designed hour is displayed.
Press the SET M button until the
designed minutes are displayed. The
display will change automatically back
to show the present time after 10 sec.
3. Press the ON/OFF button to start the air
conditioner.
4. Press the TIMER SEL button two times
to activate the OFF timer.
Low speed
C) HOW TO SET A PROGRAM FOR
DAILY ON/OFF OPERATION (OR
VICEVERSA)
1. Set the timer ON/OFF as shown in A)
and B).
2. Press the ON/OFF button to start the air
conditioner.
3. Press three times the TIMER SELECT
button to activate the DAILY timer.
NOTE
After timer setting, press PROGRAM button in order to
check the ON/OFF setting time.
7
OPERATING MODE SET TEMPERATURE CHANGE
Heating
Setting temperature Room temperature
1°C
1°C
1 hour 1 hour TIME
Lowered by 1 °C
Raised by 1 °C
HEATING
1°C
1°C
1 hour 1 hour TIME
3
4
1
2
GB