How To Set The Present Time; Cooling; Dehumidifying (Dry); Fan Only - Technibel MTF94 Bedienungsanleitung

HOW TO SET THE PRESENT TIME

1. Press the SET button for five seconds. The time indication
alone flashes.
2. Press the + or - buttons until the present time is displayed.
3. Press the SET button to stop the indication flashing.
EG

COOLING

NOTE
Verify that the unit is connected to the main
power and the STANDBY lamp is light up.
1. Set the MODE selector to COOL
2. Press the ON/OFF button and switch the
air conditioner ON.
3. Press the TEMP. buttons to set the
desired temperature (the temperature
range is between 30 °C max. and 16 °C
min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
4. Press the FAN SPEED button to select the fan speed.
NOTE
The air conditioner disposes of the condensate water automati-
cally at the HIGH and MEDIUM fan speed, on the contrary at
the LOW fan speed the condensate water is collected in the
tank.

DEHUMIDIFYING (DRY)

1. Set the MODE selector switch to "DRY"
2. Press the ON/OFF button and switch the air conditioner ON.
3. Press the TEMP. buttons to set the room temperature (the
temperature range is between 30 °C max. and 16 °C min.).
THE DISPLAY SHOWS THE ROOM
TEMPERATURE.
NOTE
G Use DRY operation when you want to reduce the humidity
in the room.
G During DRY operation, the fan speed is automatically set to
low or stops to prevent overcooling.
G
Dry operation is not possible if the indoor temperature
is 15 °C or less.
G
The humidity of the room (condensate water) will be collected
in the internal tank of the air conditioner.

FAN ONLY

If you want to make air circulate without any temperature
control, follow these steps:
1. Set the MODE selector switch to "FAN"
2. Press the ON/OFF button and switch the air conditioner
ON.
6

ADJUSTING THE FAN SPEED

AUTOMATIC
Simply set the FAN SPEED selector to the
A microcomputer automatically controls the fan speed when the
AUTO mode is selected. When the air conditioner starts
operating, the difference between the room temperature and
the set temperature is detected by the microcomputer which
then automatically switches the fan speed to the most suitable
level.
In FAN Only mode the fan speed is adjusted automatically
as in cooling mode.
.
WHEN DIFFERENCE BETWEEN
ROOM TEMPERATURE AND SET
Cooling and
dehumidifying
3
2 modes:
4
1
The above mentioned data make reference to air conditioner
operating when the sensor on the remote control unit is ON.
(Refer to temperature sensor selector). If the sensor on the unit
is being used then actual operation will slightly differ from that
described in the above tables.
MANUAL
If you want to manually adjust speed just set the FAN SPEED
selector as desired.
.

SLEEP MODE

G The SLEEP mode enables you to save energy.
1. Set the MODE selector to cool or dry.
2. Press the SLEEP button.
3. The
button again to release the SLEEP function.
What does the SLEEP mode mean?
In this mode, the air conditioner will cool or dry the room to the
set temperature, and then the thermostat will make the unit
pause. After about 1 hour, the air conditioner will automatically
reset the set temperature as follows (also refer to graph).
When the room temperature reaches the new set value, the
thermostat will cause the unit to pause. After about 1 hour the
temperature will be raised by 1°C. This enables you to save
energy without sacrificing your comfort.
.
NOTE
TEMPERATURE IS
2 °C and over
Between 2 and 1 °C
Below 1 °C
NOTE
High speed Med. speed
mark appears on the display. Press the SLEEP
COOLING AND DEHUMIDIFYING
Setting temperature
1°C
1°C
1 hour 1 hour
position.
FAN SPEED
High
Medium
Low
Low speed
Room temperature
TIME