Charger Safety; Specifications - Ryobi CSD40LI Bedienunganleitung

CSD-4030G_20 lgs 18/06/07
GB
F D E
GENERAL SAFETY RULES
Maintain power tools. Check for misalignment or
■
bindling of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
■
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.,
■
in accordance with these instructions and in the manner
intended for the particular type of power tool, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from intended could result in a hazardous situation.
BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
■
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
Use power tools only with specifically designated
■
battery packs. Use of any other battery packs may
create a risk of injury and fire.
Under abusive conditions, liquid may be ejected from
■
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
SERVICE
Have your power tool serviced by a qualified repair
■
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.

CHARGER SAFETY

Do not expose charger to wet or damp conditions.
■
Use of an attachment not recommended or sold by
■
the battery charger manufacturer may result in a risk
of fire, electric shock, or injuries to person.
To reduce risk of damage to charger body and cord,
■
pull by charger plug rather than cord when
disconnecting charger.
Make sure cord is located so that it will not be
■
stepped on, tripped over, or otherwise subjected to
damage and stress.
17:43 Page 7
I P NL S DK N
English
7
FIN GR H CZ RUS
An extension cord should not be used unless
■
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock.
If extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
b. That extension cord is properly wired and in good
electrical condition.
Do not operate charger with a damaged cord or plug.
■
If damaged, have it replaced immediately by a
qualified serviceman.
Do not operate charger if it has received a sharp
■
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman.
Do not disassemble charger; take it to a qualified
■
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of electric
shock or fire.
To reduce risk of electric shock, unplug the charger
■
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this risk.
Disconnect charger from power supply when not in use.
■
Risk of electric shock. Do not touch uninsulated portion
■
of output connector or uninsulated battery terminal.
Save these instructions. Refer to them frequently and
■
use them to instruct others who may use this unit.
If you loan someone this unit, loan them these
instructions also.

SPECIFICATIONS

Motor 4 V DC
Switch Single Speed/Reversible
No load Speed 180 r/min.(RPM)
Clutch 12 Positions
Torque 5 Nm max
Collet 6.35 mm
Weight (included battery) 0.47 kg
Charger Rating
Input 230 V-AC ~ 50Hz
Output 4.5 V-DC
160 mA
Charge Time 3-6 hours
DESCRIPTION
1. Quick change chuck
2. Forward / reverse indicator LEDs
3. LED worklight
4. Direction of rotation selector
(forward/reverse/center lock)
5. Switch Trigger
RO PL SLO HR TR