Maintenance - Elica Free Spot Montage- Und Gebrauchsanweisung

Model with button panel
B
A
E A B
A. on/off light switch
B. on/off aspiration switch and minimum power selection
B+C. medium power selection aspiration switch
B+D. maximum power selection aspiration switch
E. operating gauge (foreseen in the model with round buttons)
a
b
c
a. on/off light switch
b. off aspiration switch
c. minimum power selection aspiration switch
d. medium power selection aspiration switch
e. maximum power selection aspiration switch
Functioning - Model with display
A B C
A. OFF key (Display off) /Stand-by (led lit on the display) –
press for a long time to select the function desired.
B. Lighting, on/off.
C. Timer for selected speed (visualizes the speed selected
and flashing LED on the lower side of the display).This
knob permits the operation of the cooker hood for a
established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed P is selected.
D. Display showing:
• Fan speed (1-3-P).
• Change grease filters (grease filter saturation indicator
- F)
After washing the anti-grease filter, depress knob A
for about 3 seconds. The letter F will disappear from
the display.
D
C
C D
e
d
D E F
•
•
Attention! The active carbon filter saturation indicator is
normally deactivated, to activate it: Set the hood on OFF
(display off), press keys C and G contemporaneously for 3
secs. Initially, only letter F will fbe displayed, then after the
3 seconds have passed, letter C will be displayed as well,
indicating that the carbon filter saturation control system is
active.
To switch off the system, re-press the same two buttons:
letter C appear on display and after 3 seconds letter it
disappear and the device will be switched off.
E. Knob to decrease the speed.
F. Knob to increase the speed.
G. Timed intensive speed button: the hood operates at this
speed for 5 minutes and than returns to the previus
settings. The display will show P and a blinking dot. This
function can be cancelled by pressing button A.
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Warning! Always press the fan off button A before
disconnecting the hood from the mains supply.

Maintenance

Before performing any maintenance operation, isolate the
hood from the electrical supply by switching off at the
connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
G
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products.
DO NOT USE ALCOHOL!
Grease filter
Fig. 2
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter B, pull the spring release handle.
14
Change activated carbon filters (carbon filter
saturation indicator - C).
After replacing the charcoal filter, depress knob A for
about 3 seconds. The letter C will disappear from the
display.
When the led in the lower right side is on, it indicates
that the cooker hood is ready for operation ("standby"
position), the flashing LED indicates that the timer has
been activated for selected speed.