Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
AL-02 Laser
Item no. 59 08 18
Intended Use
The AL-02 laser is intended for generating laser light effects in light show equipment and is
controlled either manually or by using the built-in controller.
This product may only be supplied with power by the enclosed power supply unit. The power
supply unit is only approved for the connection to a 100 - 240 V/50/60 Hz power socket on the
public power supply.
The safety regulations and standards for laser operation must be complied with at all times.
The product may only be used indoors; never outdoors. Contact with moisture, for example in
bathrooms, must be avoided.
Any other use than that described above is not permitted and involves additional risks, such as
injuries to the eyes, short circuits and fi re.
No part of the product should be modifi ed or reassembled.
Read the operating instructions in full before assembling and starting to use
the laser and observe all the safety instructions included here.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume liability for any resulting damage.
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The warranty
will be void in such cases.
An exclamation mark inside a triangle indicates important instructions in the
operating manual. Please read all the instructions before using this device,
they include important information on its correct operation.
• Starting and using the product should only be done taking into consideration the require-
ments mentioned in this manual.
• For safety reasons, any unauthorised conversion and/or modifi cation to the product is not
permitted.
• Only connect the power adaptor to a normal mains socket connected to the public supply.
Before plugging in the power adaptor, check whether the voltage stated on the power adaptor
complies with the voltage of your electricity supplier.
• The laser is still connected with the mains when it is switched off. To disconnect it completely
from the mains, the mains plug has to be pulled out of the socket.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power unit from the mains socket by pulling on the cable; always use the
grips on the plug.
• For safety reasons, disconnect the power unit from the mains socket during electrical storms.
• Adjustments or maintenance should only be carried out by trained professionals who are
aware of the dangers. Improperly executed adjustments might result in dangerous laser
radiation.
• When operating the laser equipment, always make sure that the laser beam is directed so
that no one is in the projection area and that unintentional refl ected beams (e.g., from refl ec-
tive objects) cannot be directed into areas where people are present.
• Attention - Remote viewing of the laser opening with optical instruments (i.e. with a telescope or
binoculars) may be hazardous to your eyes.
• Laser radiation can be dangerous, if the laser beam or its refl ection enters unprotected eyes.
Therefore, before using the laser equipment, familiarise yourself with the statutory regula-
tions and instructions for operating such a laser device.
• Never look into the laser beam and never point it at people or animals. Laser radiation can
cause eye injuries.
• Do not point the laser beam at mirrors or other refl ective surfaces. The uncontrolled, refl ected
beam may strike people or animals.
• Never leave the laser in operation unattended.
• If possible, restrict the range of radiation by using screens or partitions.
• Wherever possible, direct the laser in such a way that it does not cross eye level.
• Caution: if operation settings or procedures others than those described here in these
instructions are used, it could result in exposure to dangerous radiation.
• This product is provided with a Class 2M Laser.
• Never look directly into the laser beam when the device is in operation. The intense light
www.conrad.com
rays could temporarily impair your eyesight. Moreover, they may trigger epileptic seizures for
vulnerable persons. This applies in particular to epileptics.
• The device is not a toy. Children and adolescents cannot judge the dangers of electrical
Version 07/11
devices and lasers.
• Inspect the laser unit from time to time for damage. Should the laser unit or the power supply
unit show any damage, disconnect them from the power supply (unplug the power supply
unit). Do not use the product afterwards, instead take it to a specialist workshop.
• Never pour out liquids above electrical devices and never leave objects (e.g. vases) fi lled with
liquids on them or in their vicinity. You run the risk of causing a fi re or a fatal electric shock. If
liquids enter the device, immediately disconnect it from the power supply, unplug the power
supply unit from the mains and consult an expert.
• Do not expose the device to high temperatures, dripping or sprayed water, strong vibrations
or heavy mechanical stress.
• Do not place open fl ames, such as burning candles, on or close to the device.
• Do not leave packing materials unattended. It may become a dangerous plaything for children.
• Do not leave the device in operation when it is unattended. For safety reasons, unplug from
the mains socket after each operation.
• Do not use the device in a tropical climate.
• If in doubt about how to connect the device correctly, or should any questions arise that are
not answered in these operating instructions, please contact our technical advisory service
or another specialist.
• Please observe the additional safety instructions in the individual chapters of this manual.
Functional Description
The AL-02 laser is equipped with a red laser, the beam of which is defl ected by two mirrors
attached to rotating shafts.
This generates various pre-programmed laser patterns that can be changed by the built-in
microphone control and can also be switched automatically or manually.
Description of the parts
(1) Mounting bracket
(2) Laser opening - Attention, the
laser beam is emitted here
(3) Power indicator
(4) Bracket locking screws
(5) DC IN low voltage socket
(6) On/Off „POWER SWITCH"
(7) MUSIC controller
(8) Function switch
(9) MANUAL SPEED key
Werbung
Inhaltsverzeichnis
