Product Description And Specifications; Intended Use; Product Features - Bosch EasyCut 50 Originalbetriebsanleitung

OBJ_BUCH-2772-002.book Page 13 Wednesday, August 24, 2016 2:29 PM
 Maintain power tools and accessories. Check for mis-
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
 Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
 Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
 Keep handles and grasping surfaces dry, clean and free
from oil and grease. Slippery handles and grasping sur-
faces do not allow for safe handling and control of the tool
in unexpected situations.
Service
 Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Safety Warnings for All-Purpose Saws
 Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
 Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the
workpiece by hand or against your body leaves it unstable
and may lead to loss of control.
 Keep hands away from the sawing range. Do not reach
under the workpiece. Contact with the saw blade can
lead to injuries.
 Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
 Pay attention that the base plate 3 rests securely on
the material while sawing. A jammed saw blade can
break or lead to kickback.
 When the cut is completed, switch off the machine and
then pull the saw blade out of the cut only after it has
come to a standstill. In this manner you can avoid kick-
back and can place down the machine securely.
 Use only undamaged saw blades that are in perfect
condition. Bent or dull saw blades can break, negatively
influence the cut, or lead to kickback.
 Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property
damage.
Bosch Power Tools
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.

Intended Use

EasyCut 50 NanoBlade/AdvancedCut 50 NanoBlade
The power tool is intended for making separating cuts and
cutouts in wood while resting firmly on the workpiece. The
saw blade recommendations are to be observed.
AdvancedCut 50 NanoBlade
The power tool is suitable for straight cuts with mitre angles of
up to 45°.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Thumbwheel for speed preselection(AdvancedCut 50)
3 Base plate
4 Handle (insulated gripping surface)
5 Auxiliary handle (insulated gripping surface)
6 Locking lever of cover
7 Cover of saw blade receptacle
8 Saw blade
9 Cutting mark, 0°
10 "Cut Control" cutting line indicator
11 Cutting mark, 45°(AdvancedCut 50)
12 "Cut Control" base
English | 13
1 609 92A 3GE | (24.8.16)