Bosch GHO 26-82 Professional Originalbetriebsanleitung Seite 13

Downloaded from www.Manualslib.com
OBJ_DOKU-27761-001.fm Page 13 Thursday, September 8, 2011 4:26 PM
Technical Data
Planer
Article number
Rated power input W
Output power W
-1
No-load speed min
Planing depth mm
Rebating depth mm
Planing width, max. mm
Weight according to
EPTA-Procedure 01/2003 kg
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =8 m/s , K=1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Bosch Power Tools
manuals search engine
Dr. Egbert Schneider
Senior Vice President
GHO 26-82
Engineering
Professional
0 601 594 1..
0 601 594 3..
710
Robert Bosch GmbH, Power Tools Division
400
D-70745 Leinfelden-Echterdingen
07.09.2011
16500
0 – 2.6
Assembly
0 – 9
Before any work on the machine itself, pull the mains
82
plug.
2.6
Changing the Tool
/II
Be cautious when replacing the planer blades. Do not
grasp the planer blades by the cutting edges. Possible
danger of injury due to the sharp cutting edges of the plan-
er blades.
Use only original Bosch carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and can be re-
versed. When both cutting edges are dull, the planer blade 13
must be replaced. The carbide blade (TC) may not be resharp-
ened.
Disassembling the Planer Blade(s) (see figure A)
To reverse or replace the planer blade 13, rotate the blade
drum 10 until it is parallel to the planer base plate 7.
Loosen the two fastening screws 12 with the Allen key
14 by approx. 1 – 2 turns.
If necessary, loosen the clamping element 11 by giving it
a light blow with a suitable tool (e.g. a wooden wedge).
Push the planer blade 13 sidewards out of the blade
drum 10 with a piece of wood.
Assembling the Planer Blade(s) (see figure B)
The guide groove of the planer blade always ensures continu-
ous height adjustment when replacing or reversing it.
If required, clean the blade seat in the clamping element 11
and the planer blade 13.
When assembling the planer blade, ensure that it is seated
properly in the blade holder of the clamping element 11. The
planer blade must be assembled and aligned centred to the
planer base plate 7. Afterwards tighten the 2 fastening
screws 12 with the Allen key 14.
Note: Before restarting, check if the fastening screws 12 are
tightened well. Rotate the blade drum 10 by hand and ensure
that the planer blade does not graze.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
English | 13
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
2 609 140 741 | (8.9.11)