Bosch GGS 8 H Professional Originalbetriebsanleitung Seite 16

OBJ_BUCH-1050-006.book Page 16 Tuesday, December 1, 2015 9:45 AM
16 | English
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
Technical Data
Straight grinder
Article number
Rated power input
Output power
Max. speed
Thread of grinder spindle
Max. spindle length
Tool holder
Max. grinding disc thickness
Grinding tool diameter, max.
Weight according to EPTA-Procedure 01:2014
Restarting Protection
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below 0.36 ohm.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-3, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 01.12.2015
1 609 92A 1FC | (1.12.15)
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
W
W
-1
min
mm
mm
mm
mm
kg
Assembly
 Before any work on the machine itself, pull the mains
plug.
Mounting the Protective Devices
 Adjust protection guards in such a manner that spark-
ing toward the operator is prevented.
Protection Guard for Grinding (GGS 8 SH) (see figure A)
Place the protection guard 2 on the spindle collar. Adapt the
position of the protection guard 2 to the requirements of the
work step. Lock the protection guard 2 with locking screw 13
and tighten the locking screw with at least 10 Nm.
Protection Guard for Grinding (GGS 8 H) (see figure E)
Place the protection guard 10 on the spindle collar. Adapt the
position of the protection guard 10 to the requirements of the
work step. Lock the protection guard 10 with the two locking
nuts 18 and tighten the locking nuts with at least 10 Nm.
After mounting the grinding tool, shut the protection guard 10
and tighten both wing nuts.
GGS 8 SH
3 601 B14 ...
1200
700
8000
M 14
31
20
32
125
4.4

/II
Bosch Power Tools