Bosch GHO 15-82 Professional Originalbetriebsanleitung Seite 13

OBJ_BUCH-865-006.book Page 13 Monday, December 1, 2014 7:58 AM
18 Scale for rebating width
19 Locking nut for adjustment of rebating width
20 Fastening bolt for parallel and beveling guide
21 Angle stop*
22 Locking nut for angle adjustment
23 Fastening bolt for rebating depth stop
24 Rebating depth stop*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Planer
Article number
Rated power input
Output power
No-load speed
Planing depth
Rebating depth
Planing width, max.
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-14.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =8 m/s , K=1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-14.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
GHO 15-82
3 601 E94 0..
W 600
W 340
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
-1
min 16000
Leinfelden, 01.12.2014
mm 0 – 1.5
Assembly
mm 0 – 9
mm 82
 Before any work on the machine itself, pull the mains
plug.
kg 2.5
Changing the Tool
/II
 Be cautious when replacing the planer blades. Do not
grasp the planer blades by the cutting edges. Possible
danger of injury due to the sharp cutting edges of the plan-
er blades.
Use only original Bosch carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and can be re-
versed. When both cutting edges are dull, the planer blade 12
must be replaced. The carbide blade (TC) may not be resharp-
ened.
Disassembling the Planer Blade(s) (see figure A)
To reverse or replace the planer blade 12, rotate the blade
drum 9 until it is parallel to the planer base plate 6.
 Loosen the two fastening screws 11 with the Hex key 13 by
approx. 1 – 2 turns.
 If necessary, loosen the clamping element 10 by giving it a
light blow with a suitable tool (e.g. a wooden wedge).
 Push the planer blade 12 sidewards out of the blade drum
9 with a piece of wood.
Assembling the Planer Blade(s) (see figure B)
The guide groove of the planer blade always ensures continu-
ous height adjustment when replacing or reversing it.
If required, clean the blade seat in the clamping element 10
and the planer blade 12.
When assembling the planer blade, ensure that it is seated
properly in the blade holder of the clamping element 10. The
planer blade must be assembled and aligned centred to the
planer base plate 6. Afterwards tighten the 2 fastening
screws 11 with the Hex key 13.
Note: Before restarting, check if the fastening screws 11 are
tightened well. Rotate the blade drum 9 by hand and ensure
that the planer blade does not graze.
English | 13
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 11E | (1.12.14)