Herunterladen Diese Seite drucken

Endress+Hauser Levelflex FMP5x Installationsaleitung

Set housing security clamp
Vorschau ausblenden

Werbung

Installation Instruction
Set housing security clamp
Levelflex FMP5x, Micropilot FMR5x, Promass 200 / TB2, Prosonic Flow 200, Promag 200, Prowirl 200
EA00038F/00/A2/16.13
712341461
Instruction is valid for the following spare part sets:
Order number
Original spare part set
71115176
Set housing security clamps, 3 pieces
We recommend that the Installation Instructions be kept with the packaging at all times.
Confirmation whether the spare part is permitted to be used with the measuring device
The spare parts set and Installation Instructions are used to replace a faulty unit with a functioning unit of the same type. 
Use genuine parts from Endress+Hauser only.
Only original spare parts supplied by Endress+Hauser shall be used with the measuring device. Therefore, before use, check whether the spare
part set is compatible with the measuring device.
A spare parts overview label is located in the connection compartment cover of the measuring device. If there is no label or the spare part is not
listed the appropriate spare part can also be identified via W@M Device Viewer.
How carrying out such a check via the W@M Device Viewer is described below:
i
Choose the Endress+Hauser Device Viewer via web browser: www.endress.com/deviceviewer
Enter the serial number (Ser. No.) of the device into the W@M Device Viewer (on the label of the transmitter), then click on "Spare parts".
The list of the available spare parts for the device is displayed.
Check the order number on the packaging label of the spare part set.
Check whether the order number of the spare part set is specified in the list displayed by the device viewer:
= YES, the spare part can be used.
= NO, the spare part may not be used.
Usage
Levelflex FMP5x, Micropilot FMR5x
Promass 200 / TB2, Prosonic Flow 200, Promag 200, Prowirl 200
Ser. No.:12345
Ser.No.:1234567890
i
www.endress.com/deviceviewer
Device Viewer
Ser. No.: 12345
71231461
=
?

Werbung

loading

  Andere Handbücher für Endress+Hauser Levelflex FMP5x

  Verwandte Anleitungen für Endress+Hauser Levelflex FMP5x

  Inhaltszusammenfassung für Endress+Hauser Levelflex FMP5x

  • Seite 1 The spare parts set and Installation Instructions are used to replace a faulty unit with a functioning unit of the same type.  Use genuine parts from Endress+Hauser only. Only original spare parts supplied by Endress+Hauser shall be used with the measuring device. Therefore, before use, check whether the spare part set is compatible with the measuring device.
  • Seite 2 (for Ex. IECEx, ATEX, FM, CSA, TIIS, NEPSI) 1, 2, 3 1 Trained customer technician 1*Trained customer technician, trained by Endress+Hauser (for repairs carried out on devices with type approval) 2 Service technician authorized by Endress+Hauser 3 Endress+Hauser (send measuring device back to manufacturer) Safety instructions •...
  • Seite 3 Set housing security clamp Tool list 3 mm 8 mm Replacing security clamp - sensor 8 mm GT18/20: 2.5 Nm GT19: 1.5 Nm Grafik Kralle2 Replacing security clamp - cover 3 mm 2.5 Nm Grafik Kralle1 Endress + Hauser...
  • Seite 4 Set housing security clamp Endress + Hauser...
  • Seite 5 Ersatzteilset und Einbauanleitung dienen dazu, eine defekte Einheit gegen eine funktionierende Einheit des gleichen Typs zu ersetzen.  Es dürfen nur Originalteile von Endress+Hauser verwendet werden. Grundsätzlich dürfen nur Ersatzteilsets verwendet werden, die von Endress+Hauser für das Messgerät vorgesehen sind. Vor der Verwendung ist deshalb zu überprüfen, ob das Ersatzteilset zum Messgerät passt.
  • Seite 6 Zulassung (z.B. IECEx, ATEX, FM, CSA, TIIS, NEPSI) 1, 2, 3 1 Ausgebildete Fachkraft des Kunden 1*Ausgebildete Fachkraft des Kunden, von Endress+Hauser geschult (für Reparaturen, die an Geräten mit Bauartzulassung vorgenommen werden) 2 Von Endress+Hauser autorisierter Servietechniker 3 Endress+Hauser (Messgerät an Hersteller zurücksenden) Sicherheitshinweise •...
  • Seite 7 Set Gehäuse Sicherungskrallen Werkzeugliste 3 mm 8 mm Austausch Gehäusesicherungskrallen - Sensor 8 mm GT18/20: 2.5 Nm GT19: 1.5 Nm Grafik Kralle2 Austausch Gehäusesicherungskrallen - Deckel 3 mm 2.5 Nm Grafik Kralle1 Endress + Hauser...
  • Seite 8 Set Gehäuse Sicherungskrallen Endress + Hauser...