Specifications - Makita DPT350 Betriebsanleitung

ENGLISH (Original instructions)
1. Red indicator
2. Button
3. Battery cartridge
4. Trigger
5. Lever
6. Sliding door
7. Bolts
8. Driver guide cover

SPECIFICATIONS

Model
Pin nail size
Pin nail magazine capacity
Dimensions (L x W x H)
Battery cartridge
Net weight
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for pressing pin nails into construction
materials such as timbers.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS NAILER SAFETY
WARNINGS
1. Always assume that the tool contains fasteners.
Careless handling of the nailer can result in
unexpected firing of fasteners and personal injury.
2. Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the
fastener causing an injury.
3. Do not actuate the tool unless the tool is placed
firmly against the workpiece. If the tool is not in
contact with the workpiece, the fastener may be
deflected away from your target.
4. Disconnect the tool from the power source when
the fastener jams in the tool. While removing a
jammed fastener, the nailer may be accidentally
activated if it is plugged in.
4
Explanation of general view
9. Lamp
10. Driver guide
11. Pin nails
12. Magazine
13. Lock lever
14. Protrusion
15. Nose adapter
16. Holder
DPT350
0.6 x 18, 25, 30, 35 mm
130 pcs
227 mm x 79 mm x 245 mm
BL1430, BL1440,
BL1415N
1.8 kg
D.C. 14.4 V
5. Use caution while removing a jammed fastener.
ENE068-1
6. Do not use this nailer for fastening electrical
GEA010-1
7. Always wear safety goggles or safety glasses with
8. Keep hands and feet away from the ejection port
9. Always remove the battery cartridge before
10. Make sure no one is nearby before operation.
GEB090-1
11. Watch your footing and maintain your balance
12. Check walls, ceilings, floors, roofing and the like
13. Use only fasteners specified in this manual. The
14. Do not tamper with the tool or attempt to use it for
15. Do not operate the tool without fasteners. It
17. Groove
18. Hook
19. Screw
20. Hex wrench
21. Material to be fastened
22. Bolt (B)
23. Bolt (A)
0.6 x 18, 25, 30, 35 mm
227 mm x 79 mm x 249 mm
BL1815,
BL1450 BL1815N, BL1820
2.0 kg 1.9 kg
The mechanism may be under compression and the
fastener may be forcefully discharged while
attempting to free a jammed condition.
cables. It is not designed for electric cable installation
and may damage the insulation of electric cables
thereby causing electric shock or fire hazards.
side shield, and a full face shield when needed.
area.
loading the fasteners, adjustment, inspection,
maintenance or after operation is over.
Never attempt to drive fasteners from both the
inside and outside of wall at the same time.
Fasteners may rip through and/or fly off,
presenting a grave danger.
with the tool. Make sure there is no one below
when working in high locations.
carefully to avoid possible electrical shock, gas
leakage, explosions, etc. caused by stapling into
live wires, conduits or gas pipes.
use of any other fasteners may cause malfunction
of the tool.
other than driving fasteners.
shortens the service life of the tool.
DPT351
130 pcs
BL1830, BL1840,
BL1850
2.1 kg
D.C. 18 V