Herunterladen Inhalt Inhalt Diese Seite drucken

Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes - EINHELL TC-CS 1200 Originalbetriebsanleitung

Handkreissäge
Vorschau ausblenden Andere Handbücher für TC-CS 1200:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
6.3 Switching ON/OFF (Fig. 9)
To switch on:
Press the locking button (3) and the ON/OFF
switch (2) at the same time
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Only exert gentle
pressure on the saw blade as you do so.
To switch off :
Release the locking button and ON/OFF switch
If you release the handle the equipment will
shut down automatically which means that it
cannot operate accidentally.
Ensure that you do not cover or block the ven-
tilation openings whilst working with the tool.
Do not slow down the saw blade after you
switch it off by pressing it sideways.
Important! Do not put down the machine until
the saw blade has reached a complete stand-
still.
Important. Carry out a trial cut in a piece
of waste wood
6.4 Changing the saw blade (Fig. 10/11)
Important. Always pull out the power plug
before doing any work on the circular saw!
Use only saw blades which comply with standard
EN 847-1 and are of the same type as the saw
blade supplied with this circular saw. Ask your
dealer for advice.
Push back and secure the moving swing
guard hood (19) using the lever for the swing
guard hood (15).
Use the saw blade wrench (13) to apply
counterpressure to the flange (18).
Undo the screw to secure the saw blade (17)
using the Allen key (a).
Remove the flange (18) and the saw blade
(12) in a downwards direction.
Clean the flange and insert the new saw bla-
de. Pay attention to the running direction (see
arrow on the guard hood and saw blade).
Tighten the screw to secure the saw blade
(17), check it runs true.
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted and
Anl_TC_CS_1200_SPK1.indb 21
Anl_TC_CS_1200_SPK1.indb 21
GB
that moving parts run smoothly and the clam-
ping screws are tightened securely.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.

8.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
- 21 -
02.02.16 09:50
02.02.16 09:50

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

43.309.36

Inhaltsverzeichnis