Safety Instructions - Ferm BSM1001 Gebrauchsanweisung

SPARE PARTS LIST FBS-800
REF NR DESCRIPTION
01 +02 CARBON BRUSH HOLDER
03 + 04 CARBON BRUSH SET
05 BELT WHEEL
06 BEARING 608-2Z
08 ROTOR
16 STATOR
17 BEARING 626-2Z
21 + 50 NEEDLE BEARING HK081210
22 SPINDLE
23 ROLL
26 SWITCH
31 BASE PLATE
41 BELT WHEEL
43 + 45 BEARING 627-2Z
44 SPIRAL GEAR
47 BIG GEAR
53 DRUM
55 ADJUSTING KNOB
73 BELT COVER
67 + 68 DUSTBAG COMPLETE
61 DRIVING BELT
30
FERM NR
409000
BELT SANDER
409001
409002
TECHNICAL SPECIFICATIONS
800608
409003
Voltage
Frequency
409004
Power input
800626
No load sander paper speed
801211 Sanding belt size
Sanding pad size
409005
Weight
409006
Lpa (Sound pressure)
Lwa (Sound power level)
409007
Vibration value
409008
409009
PRODUCTINFORMATION
800627
Fig. A
The belt sander is the perfect tool to sand wood and to
409010
grind iron, plastic or similar materials.
709011
The belt sander must be used for the rough work, for the
409012
normal sanding work an orbital sander must be used.
409013
1. On/off switch
409014
2. Front handle
409015 3. Rear handle
4. Blocking switch
409016
5. Dust collection opening
6 Adjusting knob
7. Sanding belt fastener
8. Front belt roller
9. Direction indicator
10. Drive belt cover
11. Dust bag
PACKAGE CONTENTS
1 Belt sander
3 Sanding belts
1 Dust collection bag
1 Instruction manual

1 Safety instructions

1 Guarantee card
Check the machine, loose parts and accessories for
transport damage.
Ferm Ferm
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
| 230 V~
| 50 Hz
| 800 W
Carefully read this manual before using the machine.
| 280 m/min
Make sure that you know how the machine functions and
| 75 x 533 mm
how to operate it. Maintain the machine in accordance
| 75 x 160 mm
with the instructions to make sure it functions properly.
| 3.0 kg
Keep this manual and the enclosed documentation with
| 88.6 dB(A)
the machine.
| 101.6 dB(A)
| 3.511 m/s 2
ELECTRICAL SAFETY
Always check that the power supply corresponds
with the voltage on the rating plate.
The machine is double insulated in accordance
with EN-50144; therefore no earth wire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm 2 . When using a cable reel always unwind
the reel completely.
SPECIAL SAFETY PRECAUTIONS
• If you are working with the sanding machine, wear
always ear protectors and dust mask.
• The sanding machine is not suitable for wet sanding.
• Check if the switch is not in position "ON", before
you connect the mains plug to the mains voltage.
• Keep the mains lead always away from moving parts
of the tools.
• Use safety glasses, especially when you sand above
your head.
• Do not bring pressure to your machine, this will only
delay the sanding.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
• Excessive sparking of the carbon brushes and
verticiliosis in the collector.
• Interruption of the mains plug, mains lead or mains
lead damage.
• Defect switch
• Smoke or stench of scorched isolation
3