Gude GWS 500 HM Originalbetriebsanleitung Seite 29

GWS 500 HM
priate electric tools is better and safer when within
the specifi ed power range.
b) Do not use electric tools with a defective switch.
An electric tool that cannot be switched on or off is
dangerous and must be repaired.
c) Unplug the machine and/or remove the battery
before any machine adjustment, replacement of
accessory equipment and storing the machine.
This safety measure prevents unintentional star-
ting of the electric tool.
d) Keep any electric tool that is not being used out
of reach of children. The machine must not be
used by persons not familiarised with its use and
not having read these Instructions. Electric tools
are dangerous if used by inexperienced persons.
e) Treat electric tools carefully. Check whether the
moving parts work perfectly and do not drag,
whether not broken or damaged to such an
extent that functioning of electric tools could
be aff ected. Have any damaged parts repaired
before using the machine. Poor maintenance of
electric tools is a cause of many injuries.
f) Keep the cutting tools sharp and clean. Carefully
treated cutting tools with sharp edges get stuck
less often and are easier to guide.
g) Electric tools, accessory equipment, extensions,
etc. to be used in accordance with these Instruc-
tions. Consider the working conditions and the
activity being performed. Using electric tools for
purposes other than those specifi ed may lead to
dangerous situations.
5) Service
a) Have your electric tools repaired by qualifi ed
authorised staff only, using original spare parts
only. The safety of electric tools will be maintained
by this.
Safety instructions for circular saws
for fi rewood
Operation is only allowed with a safety switch
against stray current (RCD max. stray current of
30mA).
Wear ear protectors. Exposure to noise can cause
hearing loss.
Wear gloves when handling saw blades and rough
materials.
When being operated, the machine must stand on a
horizontal and fl at surface and the fl oor around the
machine must be fl at, well-maintained and with no
waste, such as sawdust and cuttings.
The processed bundle of workpieces and fi nished
workpieces should be placed near the standard place
of work of the operator.
Switch the machine off and unplug it when unatten-
ded.
Check all screw and plug-in connections and
protective equipment if fi rm and tightened properly
and whether all moving parts are running smooth
whenever the appliance is to be put into operation.
The protective equipment on the appliance is
strictly prohibited to be disassembled, changed,
used in confl ict with the designation and it is
prohibited to attach any protective equipment of
other manufacturers.
The machine must not be used under any
circumstances if the machine or the safety devices
are damaged.
Before use check machine, cable, and plug for any
damages or material fatigue. Repairs should only be
carried out by authorised Service Agents.
Any faults with the machine, including any related to
the safeguard or the saw blades, must be reported to
the persons in charge of safety as soon as the faults
are discovered.
Before pressing On/Off , make sure the saw blade has
been fi tted properly.
The saw must not be used any longer if the cradle fails
to automatically return to the rest position.
The saw must not be used any longer if the saw
blade fails to stop in 10 seconds after switching the
machine off .
For security, use devices such as safety- and pressure
device, guide slide, rip fence, etc.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
It is necessary to refrain from removing any cuttings
and parts of workpieces from the cutting area.
Do not use saw blades which are damaged or
deformed.
Properly sharpened saw blades to be used only.
Follow instructions for use, adjustment and repair of
saw blades of manufacturers.
Do not use saw blades not corresponding to the key
data given in these instructions for use.
It is essential to adhere to the maximum speed speci-
fi ed on the saw blade.
Only use tools that meet standard EN 847-1.
Transport and store the tools in a suitable container.
To minimise noise, the tool must be sharpened and
all noise reducing elements (covers etc.) must be
properly adjusted.
Replace the table insert when worn.
Familiarise with the safety procedures for cleaning,
maintenance and regular removal of sawdust and
dust to reduce the risk of fi re.
Make sure the fl ange used is suitable for the given
purpose of use, as specifi ed by the manufacturer.
Use only original accessories and original spare parts.
Switch the machine immediately off when blocked.
Unplug the machine and remove the stuck piece of
wood.
ENGLISH
25