Technical Data; Before Putting Into Operation; Mains Connection - EINHELL RG-DP 4525 Originalbetriebsanleitung

Anleitung_RG_DP_4525_SPK7:_
chemically-based products!
Before you use the pump, clarify any possible special
conditions which need to be fulfilled for the
installation!
For example, additional safety measures may be
needed if damage to property could result from a
power failure, soiling or a defective gasket.
Examples of such safety measures: Pumps running in
parallel on a separately protected power circuit,
moisture sensors for switching off the pumps, and
similar safety arrangements.
Be sure to consult a professional plumber if you have
any doubt. The equipment can be used wherever you
want to move water, e.g. in the house, in the garden,
and for many other applications. It must not be used
to operate swimming pools!
If you want to use the equipment in bodies of water
with a natural, muddy bottom, place the equipment in
a slightly elevated position, e.g. on bricks.
The equipment is not designed for continuous
operation, e.g. as a circulating pump in a pond. In this
case the equipment's anticipated life will be greatly
shortened because the equipment was not designed
for continuous loading.
The equipment may be used only for the tasks it is
designed to handle. Any other use is deemed to be a
case of misuse. The user/operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Mains connection

Power rating
Max. pumping rate
Max. delivery head
Max. submersion depth
Water temperature max.
Hose connection approx.
47.8 mm (G 1 1/2) external thread
Max. size of foreign bodies:
Switching point height: ON
Switching point height: OFF
12.08.2011 7:35 Uhr

5. Before putting into operation

5.1 Installation
The equipment can be installed either:
Stationary with a rigid pipe line
or
Stationary with a flexible hose line
The equipment must be fastened to the suspension
eyelet with a rope (Fig. 2/Item 7).
Note:
The maximum pumping rate is possible only with the
largest possible line diameter; if smaller hoses or
pipes are connected, the pumping rate will be
reduced. If the universal hose connection (Fig. 1/Item
1) is used, it should be shortened (as shown in Fig. 4)
to the connection actually used in order not to reduce
the pumping rate unnecessarily. Flexible hoses must
be fastened to the universal hose connection with a
hose clip (not included in the scope of supply).
Note!
When installing, never hang the equipment by the
discharge line or by the power cable. The equipment
must be hung up by the provided carry handle or
suspension eyelet, or it must rest on the bottom of the
shaft. To ensure that the equipment works properly,
the bottom of the shaft always must be free of sludge
and other accumulations of dirt. If the water level is
too low, the sludge in the shaft can quickly dry out
and hinder the equipment from starting. It is
necessary therefore to check the equipment regularly
(carry out trial start-ups).
Note:
The pump shaft should measure at least
50 x 50 x 50 cm so that the floating switch can move
freely.
5.2 Mains connection
The equipment you have purchased comes with an
earthing-pin plug. The equipment is designed for
230 V ~ 50 Hz
connection to a socket outlet with earthing contact for
390 W
230 V ~ 50 Hz. Make sure that the socket-outlet is
10,000 l/h
sufficiently fused (at least 6 A) and in good working
6 m order. Insert the power plug in the socket-outlet and
the equipment is ready for operation.
8 m
35°C
Important.
To rule out danger, this work must be left strictly to a
specialist electrician or Customer Service.
Ø 25 mm
max. approx. 60 cm
min. approx. 5 cm
Seite 13
GB
13