Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Adjusting from 0° – 90 °
1.
Loosen the star handled nut (12) and turn the angle
stopper (11) until the desired angle is indicated on the
scale (0°- 90°).
2.
Refasten the star handled nut in order to fix the
adjusted angle.
3.
,
Put the tile on the stop rail (10) and the angle
stopper (11).
4. Start the machine and wait until the cooling water is
flushed to the cutting-off wheel.
5.
,
Pull the cutting unit (14) by moving the handhold
(16) slowly and constantly through the tile.
6. Switch off the machine after finishing the cut.
Setting of mitre cut
1.
Loosen the locking screws (6) on both sides of the
machine and swivel the guide bar (13) to the desired
angle position.
2.
Refasten the set screws (6).
3. Carry out the cut as described in point „Adjusting from 0°-
90°".
M
a
i
n
t
e
n
a
n
M
a
i
n
t
e
n
a
n
Before each maintenance and cleaning work
− switch off device
− wait for standstill of the stone cutter
− pull out main plug
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Maintenance
Replacing cutting-off wheel
Before replacing the cutting-off wheel
pull out the power plug.
Do not use any damaged cutting-off wheels or such which
have changed their shape.
Only use sharp cutting-off wheels.
Replacing cutting off wheel
1.
Loosen the screws (30) and swivel the cover hood (19)
to the side.
2.
Position the ring wrench (22) on the forward hexagon
nut (33) and the installation wrench (21) on the motor shaft
end and loosen the first hexagon nut (33).
Left-handed thread!
19
c
e
a
n
d
c
l
e
a
n
i
n
g
c
e
a
n
d
c
l
e
a
n
i
n
g
Loosen the 2
hexagon nut (33) in the same way.
nd
3. Remove the flange (31) toward the front.
4. Now you can remove the cutting-off wheel (20).
5. Check the spindle, hexagon nuts and flanges (31, 32) for
damages, wear or loose fit before mounting the cutting-off
wheel. Immediately replace damaged or worn parts.
6. The installation of the cutting-off wheel is carried out in
reverse order.
Observe the rotational direction! The rotational
direction arrow printed on the cutting-off wheel must agree
with the rotational direction arrow on the cover hood.
6. Firmly tighten the hexagon nuts (31).
Left-handed thread!
7. Screw on the covering cap (19).
Cleaning
Observe the following in order to keep the operability of
the stone cutter :
Clean all moving parts regularly.
Remove dust and dirt with a cloth or a brush.
Do not clean the machine with running water or high-
pressure cleaners.
Do not use solvents for the synthetic parts (petrol, alcohol,
etc.) as these can damage the synthetic parts.
Clean the collecting trough and the cooling water pump after
each application in order to guarantee the cooling of the
cutting-off wheel. To empty the trough (8), remove the
closing plug (34) and allow the water to drain into a suitable
vessel.
Clean the inside of the cover hood regularly.
Remove the mains plug before each
transport.
Transport the stone cutter only when the cutting unit is
fixed:
For this purpose screw the safety pin (27) into
the motor cover
Then screw the machine knob nut (26) open.
Vor dem Wechseln der Trennscheibe den
Fasten the cutting unit to the motor housing
Netzstecker ziehen.
using the transport screw (28).
That's how you avoid injuries on the hands.
Drain the cooling solution completely before any
transport.
A second person is required to assist with the transport.
T
r
a
n
s
p
o
r
t
T
r
a
n
s
p
o
r
t
Werbung
Kapitel
Inhaltsverzeichnis
