Description / Spare Parts - ATIKA ST 300 Originalbetriebsanleitung

parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the saw
− Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
− Damaged or illegible safety warning labels should be
replaced immediately.
Do not allow any tool key to be plugged in!
Store the unused machine in a dry locked place away from
the reach of children.
Electrical safety
Design of the connection cable according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm for cable lengths up to 25 m
2
2.5 mm for cable lengths over 25 m
2
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The device must be connected via the fitted PRCD
(residual-current-operated circuit breaker).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer
is not liable for any damage or injury resulting from such
action.
17
D e s c r i p t i o n o
D e s c r i p t i o n o
Pos. Denomination
1. Rear frame section
2. Front frame section
3.
Frame
4. Support brace
5. Lateral support
6. Locking nut for mitre cut
7. Scale for mitre cut
8. Trough
9. Table plate (3 pieces)
10. Stopper bar (2 pieces) with scale
11.
Angle fence
12. Star handled nut M6 for angle
adjustment
13. Guide bar
14. Cutting unit
15.
On-off switch
16. Handhold
17 Splash guard
18. Hose
Covering cap
19.
Cutting-off wheel Ø 200 x Ø 25,4 x 2,2
20.
mm
Installation wrench
21.
Socket wrench SW 30
22.
23. PRCD (residual-current-operated circuit
breaker)
24. Cooling water pump
25. Safety label
26. Machine knob nut M6
27. Motor safety pin
28. Transport screw for cutting unit
29.
Holding eyelet for cooling water hose
30. Hexagon screw M6 x 18
31. Front flange
32. Rear flange
33. Hexagon nut M 16 LH
34. Closing plug
35. Fan (not illustrated)
36. Fan cooling (not illustrated)
37. Capacitor (not illustrated)
38. Hose clamp (not illustrated)
f d e v i c e / s p a r e p a r t
f d e v i c e / s p a r e p a r t
Order-No.
364042
364043
364044
364045
364046
364047
364048
364049
364050
364051
364052
364053
364054
364055
364056
364057
364058
364059
364060
364067
364040
364039
364041
364061
364010
364053
364063
364064
364065
364066
364038
364070
364071
364072
364074
364075
364073
364062
s
s