Crivit 1-LD3814 Bedienungsanleitung Seite 22

Press SEL to set minutes of the timer time and confirm your setting by pressing SET.
Set the hours in the same way.
Now the additional settings for the timer will follow. Press SEL to select the desired
mode:
Cd r After reaching 0:00 the timer will count the set time again
Cd U After reaching 0:00 the timer will count forward
Cd S After reaching 0:00 the timer will stop
Exit setting mode by pressing MODE.
The timer can be started or stopped by pressing SET.
Press and hold SET to reset the timer.
After the timer time is up an alarm will sound.
Stop watch
Press MODE to select the feature before proceeding.
CHRONO ST-UHR
Press SET to start or stop the stop watch. Press SEL while the stop watch is running
to record a lap time. Up to 99 laps can be recorded.
Press and hold SET to reset the stop watch.
Memory feature
DATA ANSICHT
RECALL DATEN
Press SEL while the stop watch is stopped to display the fastest lap on the display.
Press SET to display the other lap times.
Please note: The memory feature can only be used if at least one lap time was
recorded.
Heart rate measurement
Press MODE to select the feature before proceeding.
- 83 -
Warning light
Timer
TIMER TIMER
The bottom row of the display will show the elapsed training time. The middle row
will show your heart rate and the heart rate in percent of the maximum heart rate.
The timer will start automatically when the chest belt starts measuring the heart
rate. The timer will continue counting the time if the feature mode of the watch is
changed.
Press SET to select the timer mode:
TIMER total training time
training time in heart rate target zone
training time with heart rate over target zone
▲
training time with heart rate below target zone
▼
Press and hold SET to reset the training time.
- 85 -
CHRONO CRONO
APPEL RECUP
DONNEES DATOS
If your heart rate reaches or exceeds 99% of
your maximum heart rate, or your heart rate
exceeds the target zone values (see target
zone) the red warning light will blink and an
alarm will sound.
COMPTE TEMPORIZADOR
HRM PULS
The subfeatures of the heart rate measurement can only be used when the chest
belt is connected.
Press SEL to access the subfeatures of the heart rate watch.
Timer
TIMER TIMER
Memory feature
MEMORY SPEICHER
Target heart rate
ZONE BEREICH
Calories, fat burn and BMI
CALORIE KALORIEN
Fitness
FITNESS FITNESS
LEVEL LEVEL
In the middle row of the display the heart rate is shown while wearing the chest
belt. If the signal is received from the chest belt the heart symbol will flash. To the
right of the heart rate the heart rate in percent of the maximum heart rate is shown.
The maximum heart rate is calculated by evaluating your age, weight and height.
- 84 -
Memory feature
MEMORY SPEICHER
The stored values are shown in the bottom row of the display.
maximum heart rate during training
HI H
minimum heart rate during training
LO N
average heart rate during training
AV D
Press and hold SET to reset the stored values.
Target heart rate
ZONE BEREICH
The bottom row of the display will show the lower and upper limit value of the
target zone.
The selected training type is shown on the top row of the display.
L- U user defined
L-1 Health (50-65% of maximum heart rate)
L-2 Fitness (65-80% of maximum heart rate)
L-3 Performance (80-95% of maximum heart rate)
Press and hold SET for 3 seconds to enter setting mode.
Select the training type by pressing SEL. If "U" is selected (user defined) the lower
and upper limits can be set. Press SET. The display will show the lower limit.
Set the value by pressing SEL and confirm your setting by pressing SET. Set the
upper limit in the same way.
- 86 -
FC PULSO
COMPTE TEMPORIZADOR
MEMOIRE MEMORIA
ZONE ZONA
CALORIES CALORIAS
NIV FORM NIVEL
PHYSIQ FIT
MEMOIRE MEMORIA
FO AL
FA BA
MO PR
ZONE ZONA