Crivit 1-LD3814 Bedienungsanleitung Seite 21

Using the bicycle holder
The included bicycle holder can be used to attach the wrist watch to the handlebar
of a bicycle.
Press the bicycle holder onto the top of the handlebar. Handlebars with an
especially large diameter may require the use of additional force to snap on the
bicycle holder. The heart rate monitor can now be attached to the bicycle holder
in the same way that you would attach it to your wrist.
The maximum range of 70cm between the wrist watch and the chest belt should
not be exceeded.
Light
Briefly press LIGHT to temporarily activate the light.
Important notes on the operation of the wrist watch
3 different Modes of Operation.
The watch has
- 79 -
Press and hold SET for 3 seconds to access setting mode.
The display will show
HOLD HALTEN=
TO SET EINST.
and the 12 or 24 hour selection will blink on the display.
Press SEL to select a setting and confirm your setting by pressing SET. Set the
seconds, minutes, hours, year, month and day in the same way.
Now the basic settings will follow. First the year of the birthday setting will appear
BIRTHDAY GEB-TAG
Press SEL to set the year and press SET to confirm your setting. Set the month and
day in the same way.
Now the weight will appear
WEIGHT GEWICHT
Set the digits of your weight by pressing SEL and confirm each digit by pressing
SET.
Now the height display will appear
HEIGHT GROESSE
Set each digit of your height by pressing SEL and confirm each digit by pressing
SET.
Exit setting mode by pressing MODE.
Second time zone
Press and hold SEL for 3 seconds. The watch will switch to the second time zone
display and T2 will appear on the display. Setting the second time zone can be
accomplished in the same way as described in the previous paragraph.
Press and hold SEL for 3 seconds to return to normal time mode.
- 81 -
MAINT= MANT=
REGLER AJUST
DATNAISS CUMPL-AN
POIDS PESO
TAILLE TAMANO
Press MODE to select the mode of operation of the watch.
The order of the modes is as follows:
Time and basic settings
TIME ZEIT
Stop watch
CHRONO ST-UHR
Heart rate
HRM PULS
Each mode of operation may have several subfeatures.
The subfeatures can always be accessed by pressing SEL
Speed setting
When setting numerical values, press and hold SEL to use the speed setting
feature.
Time and basic settings
Press MODE to select the feature before proceeding.
TIME ZEIT
The subfeatures of the time mode can be accessed by pressing SEL.
Time and basic settings
TIME ZEIT
Alarm
ALARM ALARM
Timer
TIMER TIMER
- 80 -
Alarm
ALARM ALARM
Press and hold SET for 3 seconds to enter setting mode.
"AL" will appear on the display and the minutes of the alarm time will blink.
Press SEL to set the minutes and press SET to confirm your setting. Set the hours in
the same way.
You may optionally set the month and day as well.
If neither month nor day are set the alarm will sound daily. If the day is set, the
alarm will sound monthly. If both the month and the day are set the alarm will
sound only at the set date.
The hourly chime setting will now appear on the display
CHIME STDALARM
Press SEL to select a setting and confirm your setting by pressing SET
(ON/EIN/ACTIF/ENCENDID=on,
OFF/AUS/INACTIF/APAGADO=off).
If the chime is activated, the bell symbol will appear and the watch will chime at
the beginning of every hour.
Exit setting mode by pressing MODE. The alarm can be activated or deactivated
by pressing SET. If the alarm is activated the alarm symbol
When the alarm sounds, press SET, SEL or MODE to stop the alarm.
Snooze feature
If no button is pressed when the alarm sounds, the alarm will shut off after 30
seconds and the symbol will blink on the display. The alarm will stop and will
resume after sounding after 2 minutes. The process will repeat itself 5 times.
Timer (max. 23:59:00)
TIMER TIMER
Press and hold SET for 3 seconds to enter setting mode.
The minutes of the timer time will blink on the display.
- 82 -
TEMPS HORA
CHRONO CRONO
FC PULSO
SEL.
SEL SEL
TEMPS HORA
TEMPS HORA
ALARM ALARMA
COMPTE TIMER
ALARM ALARMA
SIGN HOR HORA AL
will appear.
COMPTE TIMER