THOMSON ROC4239 Bedienungsanleitung Seite 2

ROC4239
2
4
6
8
10
12
14
16
18
20
22
24
A B
CR2032
STB
DVD
TV
AUX
1
3
5
7
9
11
13
ROC
15
4239
17
19
21
23
C
1
5
9
13
17
1x
1x
1x
21
25 This universal remote control (4 in 1) is compatible with the majority of television sets, DVD pla-
yers and video recorders, as well as digital boxes such as satellite or cable receivers, DVBT recei-
29
vers (Digital Video Broadcast Terrestrial), ADSL decoders, and so on.
33
This remote control was programmed in the factory, so that you can use it to control most of the
sets of the THOMSON group's make. For this reason, we recommend that prior to attempting to
37
programme the remote control, you try it out by means of one of the methods described in this
41
user manual. However, first of all, please activate the remote control by removing the 2 protective
45 tabs from the 2 CR 2032 batteries.
Please keep this guide along with the code list (provided separately), so that you can subsequent-
49
ly programme your remote control for use with other sets.
53
The keys
57
61
1: On/Standby or Standby only, depending on
the equipment being used.
2 Mode keys: Select the device to control
(TV, DVD, ...).
3 Setup: Allows you to program your remote before
the first use. It also allows you to access to
secondary functions of certain A/V
appliances (Shift). Press and release the
„Setup" key followed by the function key you
want.
4 Learn: Used for the learning codes procedure (key
copying) (see page 3).
5: Displays information of the selected
appliance.
6: Teletext On.
7: Teletext Off.
8: Teletext Hold (stop page scrolling).
9 Exit: Turn off the menu of the selected
product.
10 (Mute): Switches the selected appliance sound
off.
11 Menu: Turns on the menu of the selected
product.
12 V-, V+: Increases (+) or decreases (-) the volume
of the selected device.
13 P+, P-: Channel Up and Channel Down buttons.
14: Allow you to navigate the menus
horizontally and verticaly.
15 OK: Confirms a selection.
16 (play): Play a DVD disc (DVD)*.
17: Fast forward (DVD)*.
18 (rewind): Goes backward (DVD)*.
19 (pause): Suspends play and stops on an image*.
20 (record): To record, press the RECORD key twice.
21 (stop): Stop the disc (DVD)*.
22 Numeric keys 0 - 9: These keys have the same
functions as those of your original
remote and are also used to enter the
codes for different products.
23 -/--: In connection with the numeric keys, this
button allows you, with some equipment,
to select directly channels with 2 digits.
24 AV: For selecting an external source (SCART,
HDMI, ...).
* The coloured buttons can be used to select
categories when teletext is activated, and specific
functions depending on the make.
Testing the remote control before
you programme it
1. Turn on the product you want to control.
2. Press the Mode key that corresponds to the type of
product you want to control:
TV: television set, DVD: DVD player, SAT: satellite
receiver, AUX: any other equipment.
3. Direct the remote control towards your equipment
and try to switch it off by simply pressing the
key G. If the device does not turn off, you must
program the remote control using one of the
methods A, B, C or D described hereafter.
Note 1: Except for the TV key, the DVD, SAT and AUX
mode keys can be programmed to control a device
other than that indicated on the key. It is therefore
possible, for example, to allocate SAT mode to the
DVD key. You must enter the code corresponding to
the manufacturer and the device by using one of the
methods indicated in this manual.
However, method D (automatic search for a code)
will greatly simplify the task for you. In this case it
is only necessary to enter a code from the list that
1
corresponds to the type of device, for example: 0603
for a Thomson satellite receiver) and then to run the
automatic search procedure. The remote control will
then test all the codes automatically until it finds those
that control the receiver.
Note 2: To control 2 devices of the same type and the
same brand (2 Thomson AUXs, 2 Thomson satellite
receivers, ...) ensure first that these two devices are
not set to react to the same sub code, they will require
one sub code for one and a different sub code for
the other (i.e., codes A and B with Thomson devices).
Once you have checked this, successively program 2
separate mode keys using method D.
Programming
the remote control
Method A – Fast programming
with 1-digit subcode
Before you start programming, you must find the
subcode of the set to be controlled. Entering a
subcode lets the remote control test a predefined list of
codes. Refer to the list provided with these instructions,
page I of the subcodes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp flashes
to signal that this time is almost up, and then goes
off).
3. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, SAT: satellite
receiver, cable, DVBT, ADSL, AUX: any other
appliance.
4. While the indicator is lit, type in the subcode
(example: 1 for THOMSON).
5. Direct the remote control towards the set and try to
switch it off by pressing the key G.
6. If the set you want to control switches off, press OK
to memorise the code.
7. Should the set not switch off, press key G repeatedly,
until the set switches off. Between two key presses,
leave enough time for the key corresponding to the
selected mode enough time to light up again (about
1 second). Proceeding this way will enable you to
see whether the set responds or not.
8. Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Method B – 4-digit codes
programming
Before you start programming, you must find the code
of the set to be controlled.
Refer to the list provided with these instructions, page
II of the codes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp flashes
to signal that this time is almost up, and then goes
off).