Lock Nut; General Power Tool Safety Warnings; Inner Flange; Lock Nut Wrench - Makita DGA405 Betriebsanleitung

ENGLISH (Original instructions)
1. Button
2. Red indicator
3. Battery cartridge
4. Lock-off lever
5. Switch lever
6. Battery indicator
7. Mode indicator
8. Shaft lock
9. Wheel guard
10. Bearing box
11. Screw
12. Lever

13. Lock nut

SPECIFICATIONS
Max. wheel thickness
Rated speed (n)/No load speed (n
With battery cartridge BL1815N, BL1820
Overall length
With battery cartridge BL1830, BL1840, BL1850
With battery cartridge BL1815N, BL1820
Net weight
With battery cartridge BL1830, BL1840, BL1850
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS GRINDER SAFETY
WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
6
Explanation of general view
14. Depressed center wheel

15. Inner flange

16. Lock nut wrench

17. Ezynut

18. Abrasive wheel
19. Spindle
20. Arrow
21. Notch

22. Flex wheel

23. Plastic pad

24. Sanding lock nut

25. Abrasive disc

26. Rubber pad

Model
Wheel diameter
Spindle thread
Rated voltage
GEA010-1
GEB059-3
DGA405
100 mm (4")
6 mm (1/4")
)
0
2.2 kg
2.4 kg
Failure to follow all instructions listed below may result
ENE048-1
in electric shock, fire and/or serious injury.
2. Operations such as polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
27. Abrasive cut-off wheel/diamond
wheel
28. Wheel guard for abrasive cut-off
wheel/diamond wheel
29. Abrasive cut-off wheel
30. Diamond wheel
31. Thickness: Less than 4 mm (5/32")
32. Thickness: 4 mm (5/32") or more
33. Wire cup brush
34. Wire wheel brush
35. Exhaust vent
36. Inhalation vent
37. Dust cover
DGA455
115 mm (4-1/2")
6 mm (1/4")
M10 M14 or 5/8" (country specific)
8,500 min
348 mm
362 mm
2.3 kg
2.5 kg
D.C. 18V
DGA505
125 mm (5")
6 mm (1/4")
-1
2.3 kg
2.6 kg