Inner Flange; Lock Nut; Rubber Pad; Sanding Lock Nut - Makita GA5040 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Slide switch
4-1. Wheel guard
4-2. Bearing box
4-3. Screw
5-1. Wheel guard
5-2. Bearing box
5-3. Screw
5-4. Lever
6-1. Screw
6-2. Lever

7-1. Lock nut

7-2. Depressed center wheel

7-3. Inner flange

8-1. Lock nut wrench

SPECIFICATIONS
Model
Wheel diameter
Spindle thread
Rated speed (n) / No load speed (n
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model GA4040, GA4540, GA5040
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Model GA6040
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Explanation of general view
8-2. Shaft lock
9-1. Ezynut
9-2. Abrasive wheel
9-3. Inner flange
9-4. Spindle
10-1. Shaft lock
11-1. Arrow
11-2. Notch
13-1. Lock nut
13-2. Flex wheel
13-3. Plastic pad
13-4. Inner flange

14-1. Sanding lock nut

14-2. Abrasive disc

14-3. Rubber pad

GA4040
100 mm (4")
M10
) 11,000 min
0
303 mm
2.3 kg
ENE048-1
ENF002-2
ENG905-1
) : 86 dB(A)
pA
) : 97 dB(A)
WA
) : 87 dB(A)
pA
) : 98 dB(A)
WA
GA4540 GA4541
115 mm (4-1/2")
M14
-1 -1
11,000 min
303 mm 325 mm
2.4 kg 2.7 kg
Model GA4541, GA5041
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model GA4040
Work mode : surface grinding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding with normal side grip
Vibration emission (a
4
15-1. Marking A
15-2. Marking B
15-3. Marking C
15-4. Marking D
17-1. Lock nut
17-2. Abrasive cut-off wheel/diamond
wheel
17-3. Inner flange
17-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
18-1. Wire cup brush
19-1. Wire wheel brush
20-1. Exhaust vent
20-2. Inhalation vent
GA5040 GA5041
125 mm (5")
M14
-1
11,000 min
303 mm 325 mm
2.4 kg 2.7 kg
/II
) : 84 dB(A)
pA
) : 95 dB(A)
WA
Wear ear protection
2
) : 6.0 m/s
h,AG
2
2
) : 5.5 m/s
h,AG
2
2
) : 2.5 m/s
h,DS
GA6040
150 mm (6")
M14
-1
9,000 min
303 mm
2.5 kg
ENG900-1
or less