Herunterladen Inhalt Inhalt Diese Seite drucken

Datenformat Des Ausgangssignals; Codierung Des Statusbytes Beim Pa-Ausgangswert - VEGA VEGAPULS 63 Betriebsanleitung

Vorschau ausblenden Andere Handbücher für VEGAPULS 63:
Inhaltsverzeichnis

Werbung

11 Anhang

Datenformat des Ausgangssignals

Byte2 Byte1 Byte0
Byte4 Byte3
Status
Value (IEEE-754)
Abb. 50: Datenformat des Ausgangssignals
Das Statusbyte entspricht dem Profil 3.02 "Profibus PA Profile for Process Control Devices" codiert.
Der Status "Messwert OK" ist als 80 (hex) codiert (Bit7 = 1, Bit6 ... 0 = 0).
Der Messwert wird als 32 Bit Gleitpunktzahl im IEEE-754-Format übertragen.
Byte n
Bit
Bit
Bit
Bit
Bit
Bit
7
6
5
4
3
2
VZ
2
7
2
6
2
5
2
4
2
3
Sign
Exponent
Bit
(Exponent - 127)
VZ
Value = (-1)
2
Abb. 51: Datenformat des Messwerts

Codierung des Statusbytes beim PA-Ausgangswert

Weitere Informationen zur Codierung des Statusbytes finden Sie in der Device Description 3.02 auf
www.profibus.com.
Statuscode
0 x 00
0 x 04
0 x 0C
0 x 10
0 x 1f
0 x 44
0 x 48
0 x 4c
0 x 51
70
Byte n+1
Bit
Bit
Bit
Bit
Bit
Bit
Bit
1
0
7
4
6
5
3
2
2
2
0
2
2
-2
2
-3
2
-4
2
1
-1
Significant
(1 + Significant)
Beschreibung lt. Profi-
busnorm
bad - non-specific
bad - configuration error
bad - sensor failure
bad - sensor failure
bad - out of service con-
stant
uncertain - last unstab-
le value
uncertain substitute set
uncertain - initial value
uncertain - sensor; con-
version not accurate - low
limited
Byte n+2
Bit
Bit
Bit
Bit
Bit
Bit
Bit
7
6
5
4
0
2
1
2
2
-9
2
-10 -11 -12 -13 -14 -15 -16 -17
2
2
2
-6
2
-7
-8
-5
Significant
Mögliche Ursache
Flash-Update aktiv
– Abgleichfehler
– Konfigurationsfehler bei PV-Scale (PV-Span too
small)
– Maßeinheit-Unstimmigkeit
– Fehler in der Linearisierungstabelle
– Hardwarefehler
– Wandlerfehler
– Leckpulsfehler
– Triggerfehler
– Messwertgewinnungsfehler
– Temperaturmessungsfehler
"Out of Service"-Mode eingeschaltet
Failsafe-Ersatzwert (Failsafe-Mode = "Last value" und
bereits gültiger Messwert seit Einschalten)
– Simulation einschalten
– Failsafe-Ersatzwert (Failsafe-Mode = "Fsafe value")
Failsafe-Ersatzwert (Failsafe-Mode = "Last valid value"
und noch kein gültiger Messwert seit Einschalten)
Sensorwert < untere Grenze
Bit
Bit
Bit
Bit
Bit
Bit
Bit
3
2
1
0
7
6
5
2
2
2
2
-18 -19 -20 -21 -22 -23
2
2
2
VEGAPULS 63 • Profibus PA
Byte n+3
Bit
Bit
Bit
Bit
Bit
4
3
2
1
0
2
2
2
2
2
Significant

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis