Before Starting The Equipment - EINHELL TC-TC 618 Originalbetriebsanleitung

tive. The manufacturer's liability shall be deemed
void if the machine is modifi ed in any way and the
manufacturer shall therefore accept no liability for
any damages arising as a result of modifi cations.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine's construction and
design:
•
Contact with the diamond cutting wheel whe-
re it is not covered.
•
Contact with the diamond cutting wheel while
it is turning.
•
Defective diamond tips flying off the cutting
wheel.
•
Kick-back of workpieces and parts of workpi-
eces due to improper handling.
•
Damage to hearing if ear-muffs are not used
as necessary.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

6. Before starting the equipment

•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the diamond wheel to
run freely.
•
Before you actuate the ON/OFF switch, make
sure that the diamond wheel is correctly fit-
ted and that the machine's moving parts run
smoothly.
•
Before you connect the machine to the power
supply, make sure the data on the rating plate
is the same as that for your mains.
•
Before using the machine, check all of the
parts for damage and replace any parts that
are damaged. When replacing any parts or
accessories, always carefully follow the inst-
ructions in this manual.
•
For optimum performance and maximum sa-
fety, keep the machine clean at all times.
•
Check the machine cable at regular intervals.
•
While the machine is running, check the wea-
ring parts and the fastenings of parts which
may have become loose and check that all
Anl_TC_TC_618_SPK1.indb 17 Anl_TC_TC_618_SPK1.indb 17
GB
accessories are correctly fitted.
•
Notice! The tile cutting machine is desig-
ned for use with water.
•
Check that the water level is high enough to
cover the diamond part of the wheel each
time before you start a cutting operation and
keep checking it during cutting as well. Fill/
refill the cooling water directly into the trough.
6.1 Changing the diamond cutting wheel
(Fig. 2/3)
To replace the wheel when worn, proceed as
follows:
•
Pull out the power plug first.
•
Take out the water trough (5).
•
Remove the side cover (17).
•
Apply an 8 mm counterholder to block the
motor shaft.
•
Unscrew the lock nut (18) on the wheel flange
(16) with a 19 mm wrench.
•
Clean the wheel flange thoroughly once the
wheel has been removed.
•
Take out the worn diamond cutting wheel (15)
and fit the new one to the flange, then fit the
outer flange (16) and tighten with the nut (18).
•
Fasten the side cover (17) again.
•
Check that the diamond wheel rotates in the
correct direction!
6.2 Adjusting the top wheel guard Fig. 1/6)
•
Insert the splitter (19) through the table and
into the holder (11) from above and fasten
with the screws (20).
•
Move the wheel guard to approximately 5 mm
above the tile you wish to cut. Lock the wheel
guard (3) in position with the knurled screw
(9) as shown in Fig. 1.
•
Notice!The machine is fitted with a cutting
wheel with a non-segmented edge.
- 17 -
26.05.15 09:33 26.05.15 09:33